background image

                                           

Beijing Huahuan Electronics Co., Ltd

 

Huahuan 

                       

- 16 -                                        TDMUX-16 User Manual      V1.2

 

Table 5.3-3 Ethernet management parameters   

Parameters  

Options  

Explanation  

Eth Port 

Status 

Port 

 

6 Ethernet ports number 

Service No. 

Ethernet service No.: support at most 20 capital/small 
letters, digit and part special character input. Chinese 
character support 2 numbers( not support some special 
characters, as “ / ”

“ \ ” input. 

Link 

Link: indicate current Ethernet link(Up/Down) 

Speed 

Speed 10/100/1000Mbps: indicate current Ethernet port 

speed 

Duplex 

Duplex: indicate current Ethernet work mode (half/full) 

Mode 

Auto 
1000M 
full 
100M full   
100M 
half  
10M full 
10M half 

6 Ethernet ports work mode configuration: 
Adaptive (default) 
1000M full 
100M full   
100M half   
10M full 
10M half 
Electrical interface work modes have Auto, 100M full, 
100M half, 10M full and10M half. 
Optical interface work modes have Auto, 1000M full, 
100M full and 100M half 

Alarm Mask 

 

Set Ethernet interface alarm mask 

Note: The sentence with underline is default settings. 

 

Fig 5.2-2 E1/T1 line management interface 

E1/T1 service management parameters setting are given as below table: 

 

Summary of Contents for H0FL-ETHMUX V16
































Reviews: