manualshive.com logo in svg

HTP Pioneer, Installation And Startup Manual

The Majacraft Pioneer user manual is a comprehensive guide on how to assemble and operate this exceptional spinning wheel. This manual is available for free download from our website, where you can easily access step-by-step instructions and detailed illustrations to enhance your spinning experience.

Share
Download
background image

5 

 

 

                                                                                    LP- 325 REV. 3.3.15 

K. MULTIPLE APPLIANCES ......................................................................................................................................................... 21

 

L. CENTRAL HEATING PIPING DETAIL ...................................................................................................................................... 22

 

M. PIPING INTO THE DHW PACK ON THE VERSA-FLAME ...................................................................................................... 24

 

E. MIXING VALVE INSTALLATION .............................................................................................................................................. 25

 

O. VERSA-FLAME DHW PERFORMANCE .................................................................................................................................. 27

 

P. DHW PIPING WITH THE VERSA-FLAME ............................................................................................................................... 29

 

PART 5 

– VENTING, COMBUSTION AIR AND CONDENSATE REMOVAL............................................................................ 31

 

A. GENERAL ................................................................................................................................................................................ 32

 

B. APPROVED MATERIALS FOR EXHAUST VENT AND INTAKE PIPE .................................................................................... 32

 

C. REQUIREMENTS FOR INSTALLATION IN CANADA ............................................................................................................. 33

 

D. EXHAUST VENT AND INTAKE PIPE LOCATION ................................................................................................................... 34

 

E. EXHAUST VENT AND INTAKE PIPE SIZING .......................................................................................................................... 35

 

F. LONGER VENT RUNS ............................................................................................................................................................. 35

 

G. EXHAUST VENT AND INTAKE PIPE INSTALLATION ............................................................................................................ 36

 

H. VENTING DRAWINGS ............................................................................................................................................................. 37

 

1. DIRECT VENT INSTALLATION OF EXHAUST VENT AND INTAKE PIPE ........................................................................................................ 37

 

2. VENTING THROUGH AN EXISTING SYSTEM ................................................................................................................................................. 41

 

3. INDOOR COMBUSTION AIR INSTALLATION IN CONFINED OR UNCONFINED SPACE ............................................................................... 43

 

I. CONDENSATE REMOVAL SYSTEM ........................................................................................................................................ 45

 

PART 6 

– FIELD WIRING .......................................................................................................................................................... 46

 

A. INSTALLATION MUST COMPLY WITH: .................................................................................................................................. 46

 

B. FIELD WIRING ......................................................................................................................................................................... 48

 

C. LINE VOLTAGE WIRING FOR STANDARD APPLIANCE ....................................................................................................... 48

 

D. THERMOSTAT ......................................................................................................................................................................... 48

 

E. OUTDOOR SENSOR (OPTIONAL) .......................................................................................................................................... 49

 

F. INDIRECT SENSOR (OPTIONAL) ........................................................................................................................................... 49

 

G. 0-10 VOLT BUILDING CONTROL SIGNAL (OPTIONAL) ........................................................................................................ 49

 

H. UL353 LOW WATER CUT-OFF INTERFACE KIT (OPTIONAL) .............................................................................................. 49

 

I. WIRING OF APPLIANCE ALARM (OPTIONAL) ........................................................................................................................ 49

 

J. VERSA-FLAME WIRING FOR DHW PRIORITY WITH ZONE VALVES OR CIRCULATORS .................................................. 50

 

1. WIRING WITH ZONE VALVES .......................................................................................................................................................................... 50

 

2. WIRING WITH ZONE CIRCULATOR PUMPS ................................................................................................................................................... 50

 

K. WIRING OF CASCADE SYSTEM COMMUNICATION BUS (PIONEER ONLY) ...................................................................... 51

 

L. CASCADE MASTER PUMP AND SENSOR WIRING (PIONEER ONLY) ................................................................................ 51

 

M. CASCADE FOLLOWER PUMP AND SENSOR WIRING (PIONEER ONLY) .......................................................................... 51

 

PART 7 

– GAS CONNECTIONS ............................................................................................................................................... 52

 

A. GAS PIPING ............................................................................................................................................................................. 53

 

B. GAS TABLE .............................................................................................................................................................................. 53

 

C. GAS VALVE ............................................................................................................................................................................. 54

 

PART 8 

– START-UP PREPARATION...................................................................................................................................... 54

 

A. CHECK FOR GAS LEAKS ....................................................................................................................................................... 55

 

Summary of Contents for Pioneer











































































Reviews:

No comments

Related manuals for Pioneer

Watts Aerco BMK 5000 Operation And Service Manual preview
Aerco BMK 5000
Brand: Watts Pages: 167
AJAX A050-A300 Operating Instructions Manual preview
A050-A300
Brand: AJAX Pages: 116
Gabarron MATTIRA MAS18 Installation Instructions And User Manual preview
MATTIRA MAS18
Brand: Gabarron Pages: 44
Orlanski ORLAN SUPER 130 kW Instruction Manual & Service Manual preview
ORLAN SUPER 130 kW
Brand: Orlanski Pages: 35
Jaspi PELLETTI XL Installation And Operation Manual preview
PELLETTI XL
Brand: Jaspi Pages: 13
A.O. Smith Burkay Genesis GB-1000 Assembly preview
Burkay Genesis GB-1000
Brand: A.O. Smith Pages: 2
Vaillant ecoTEC plus 612 Instructions For Use Manual preview
ecoTEC plus 612
Brand: Vaillant Pages: 20
Buderus Logano plus GB102 User Instructions preview
Logano plus GB102
Brand: Buderus Pages: 12
Chaffoteaux & Maury CORVEC 28 BF Installation Manual preview
CORVEC 28 BF
Brand: Chaffoteaux & Maury Pages: 16
Chaffoteaux & Maury CHALLENGER 30 OF Installation And Servicing Instructions preview
CHALLENGER 30 OF
Brand: Chaffoteaux & Maury Pages: 20
Chaffoteaux & Maury CHALLENGER 30 FF Installation And Servicing Instructions preview
CHALLENGER 30 FF
Brand: Chaffoteaux & Maury Pages: 24
HTP EnduroTI ETI-1000 Installation, Start-Up, Maintenance, Parts, Warranty preview
EnduroTI ETI-1000
Brand: HTP Pages: 67
HTP Mod Con 300 HL Installation & Maintenance Manual preview
Mod Con 300 HL
Brand: HTP Pages: 83
OERTLI GMR 6160 Technical Information preview
GMR 6160
Brand: OERTLI Pages: 4
Columbia CEG E Series Installation, Operation & Maintenance Manual preview
CEG E Series
Brand: Columbia Pages: 32
Electro Industries Mini-Boiler BH309 Installation & Operating Instructions Manual preview
Mini-Boiler BH309
Brand: Electro Industries Pages: 18
HTP EL-110 Installation & Start-Up Manual preview
EL-110
Brand: HTP Pages: 85
Truma BS 10 Operating Instructions Manual preview
BS 10
Brand: Truma Pages: 28

Brands by name

Popular brands

Load more brands