HTL DS Series Operating Instructions Manual Download Page 4 | Manualshive

Page: 4 / 32

background image

OUTSIDE UK: +44 (0) 1670 700 018

3

Introduction

This manual is designed to provide you with the basic knowledge required to operate and maintain
your wrench. Please read this manual carefully and follow the instructions provided. If you have any
questions regarding your HTL Wrench, please call us on +44 (0) 1670 700 018 or alternatively
email us: [email protected].

Your purchase of this wrench entitles you to the following FREE services:

•

Free training in the application and operation of your HTL equipment.

•

Free engineering assistance.

•

Free loan wrenches in case of failure during the warranty period.

Worldwide Warranty

HTL equipment is engineered to the latest technological standards and is accompanied by a 12 month
warranty. Should your new equipment fail under normal use within 12 months, we will repair or replace
your damaged equipment.

HTL-Operating-Instructions-DS.indd 4

11/04/2017 10:15

«
...
2
3
4
5
6
...
»

Summary of Contents for DS Series

































Reviews:

No comments

Related manuals for DS Series

Brand: 3Com Pages: 2

Brand: Ebinger Pages: 33

Brand: Graco Pages: 2

Brand: Neilsen Pages: 10

Brand: VADANIA Pages: 5

Brand: UCAN Pages: 22

Brand: Velleman Pages: 33

Brand: Xtreme Pages: 10

Brand: Aliaxis Pages: 24

Brand: Grizzly Pages: 80

Brand: BGS technic Pages: 12

Brand: TDK-Lambda Pages: 18

Brand: Baileigh Pages: 24

Brand: Baileigh Industrial Pages: 40

Brand: Parkside Pages: 51

Brand: Paxton Pages: 3

SonnenProtect 1300-AU-IN-ATS

Brand: Sonnen Pages: 20

Brand: Parkside Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands