manualshive.com logo in svg

HSM SP 5088, Operating Manual, Page: 39 / 60

Share
Download
HSM SP 5088 Operating Manual Download Page 39

07/2013 

2.991.999.120_en

 

  

39

SP 5088

Note
The fi rst bales compressed during the running-in of the baling press are
not yet perfectly compressed and shaped. Even compressing the
ejected compression material again does not result in an optimum bale.

– Switch on the main switch on the baling press

– Reload the unstrapped "running-in material" from the beginning through the inspection 

fl ap into the baling press

– Close the inspection fl ap

– Press the "Press ram forwards" key and compress all "running-in material" in this  

manner

– Press the "Automatic operation" key

– Following you can continue working automatically with the equipment

4.4.1 

Setting the press channel adjustment cylinder

The material is compressed and pushed into the conical press channel. The press
channel opens and closes depending on the pressure. 

The opening speed of the press channel can or must be adjusted depending on the type
of material to be pressed (frictional resistance).

Note

The press channel should open smoothly – not with a sudden jerk!

Close

 the throttle screw to open the press channel more 

slowly  

 

Open

 the throttle screw to open the press channel more 

quickly

 

Basic setting: 
Close the throttle screw completely and open it by 

1/8 of a turn

.

Summary of Contents for SP 5088





























































Reviews:

No comments