manualshive.com logo in svg

HSM SP 5088, Operating Manual, Page: 21 / 60

Share
Download
HSM SP 5088 Operating Manual Download Page 21

07/2013 

2.991.999.120_en

 

  

21

SP 5088

3.5 

Transporting the baling press

Always use the special bearing points for loading the machine from a lorry using a forklift. 

– Place the baling press on a smooth level surface at the installation site.

– Remove the packaging foil and dispose of it in a manner that is environmentally 

sound. 

– Cut through the steel straps.

– Using a forklift, lift the baling press by approximately 10 cm and remove the wooden 

blocks.

– Open the inspection fl ap and remove all the items delivered with the machine from the 

press chamber.

3.5.1 

Transport to another application site

Over short distances the channel baling press can be rolled to the operating site.
Ensure that the load on the foundation is accounted for and the space requirements
fulfi lled at the new installation site. An approved electrical connection must be available
at the new installation site.

Caution!

Installations on the electrical system or control cabinet may only be car-
ried out by a qualifi ed electrician or one of our service engineers.

Summary of Contents for SP 5088





























































Reviews:

No comments