manualshive.com logo in svg

HSM SP 5088, Operating Manual, Page: 29 / 60

Share
Download
HSM SP 5088 Operating Manual Download Page 29

07/2013 

2.991.999.120_en

 

  

29

SP 5088

“Bale ready” LED (9)

This symbol lights up blue as soon as the bale has reached a set size. The press ram
stops, and the press and shredder switch off. 

Indicator: Bale ready
                 2-hand control

The “Press ram status” symbol lights up yellow on the shredder control panel. The cutting
unit of the shredder can now only be run backwards. 

The “Bale ready” message remains active until the counter plate is closed. Then the 

Indicator:  Manual mode
                  Bale number: xxx 

(= daily bale meter reading) appears.

“Malfunction” LED (10)

This symbol lights up red as soon as a malfunction occurs in the baling press. The press
and shredder switch off. 
(-> see also “

Malfunctions

”)

The machine cannot be started whilst this message is active!

+ / – Keys (11.1)

Press the +/– keys to scroll through the menu items.
See also the following pages.

+ Key (11.2)

Pressing this will open the bale channel and pressure-relieving
 

Text display (12)

The text display shows the operating conditions and error messages.    

 

 

(-> see also “

Malfunctions

”)

Summary of Contents for SP 5088





























































Reviews:

No comments