manualshive.com logo in svg

HRS RXR Audio Stand, Manual

Share
Download
HRS RXR Audio Stand Manual Download Page 2

 

Introduction 

 

 

 
Thank you for purchasing the Harmonic Resolution Systems, Inc. (HRS) RXR 
Audio Stand.  When used properly, it will give you many years of superior musical 
or video signal reproduction. 
 
 
The RXR Audio Stand significantly reduces the negative impact of structure-borne 
noise on your audio or video component performance.  Decades of engineering 
experience, custom material development, and listening tests are incorporated 
into the design of the RXR Audio Stand.  This high performance product from 
Harmonic Resolution Systems, Inc. will enable your audio/video source and 
amplification components to achieve high levels of performance. 
 
 
The RXR Audio Stand, which includes the HRS Isolation Base as the primary shelf 
system, is a perfect match for the HRS Damping Plates and Nimbus Products.  
While the RXR Audio Stand and Isolation Bases work to significantly reduce 
structure-borne noise, the HRS Damping Plates and Nimbus Products 
significantly reduce the harmful effects of air-borne noise and structural 
resonance on your components. 
 
 
Please read this manual 

completely

 prior to assembly and use of your RXR Audio 

Stand.  It contains instructions necessary for proper assembly, use, and care of 
this system.  Proper care of your RXR Audio Stand will ensure optimum 
performance and an aesthetically appealing system. 
 
 

Summary of Contents for RXR Audio Stand


















Reviews:

No comments

Brands by name

Popular brands

Load more brands