HRS DF19G Series Instruction Manual Download Page 7

Page: 7 / 16

- 4 -

III. Operating procedure

1. Mounting the ground plate

1) Face upward signal face

②

of FPC

①

and polarization

mark

④

of the ground plate

③

2) Mount the ground plate

③

so that you do not touch

signal section

②

of FPC by hand.

FPC

①

Polarization mark

④

Ground plate

③

FPC

①

Polarization mark side

④

Signal face

②

Ground plate

③

2. Inserting FPC

1) Adjust connector main body

②

and polarization mark

④

of the ground plate

③

to the same direction.

2) Insert FPC

①

until it comes in contact with the inside of

connector main body

②

FPC

①

Connector main body

②

Insertion

Connector main body

②

FPC

①

Cautions when inserting FPC

1. The connector main body and the ground

plate

will be broken at the time of connec

tion unless the connector main body and
the polarization

mark of the ground plate

are set in the same direction.

2. Insertion may be difficult when FPC is warped.

Ground plate

③

Polarization mark

④

Adjust the direction of FPC referring to

polarization mark " " of the ground plate.

Summary of Contents for DF19G Series
















Search results

Summary of Contents for DF19G Series

Reviews:

Related manuals for DF19G Series

Brands by name

Popular brands

HRS DF19G Series, Instruction Manual

Search results

Summary of Contents for DF19G Series

Reviews:

Related manuals for DF19G Series

Brands by name

Popular brands