background image

3 Connecting to a Windows NT Server 3.51

Windows for Workgroups Version 3.11

3 Connecting to a Windows NT Server 3.51

Windows for 

Workgroups 

Version 3.11

Requirements

HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

3COM Etherlink 3C900 Ethernet card and drivers disk ver. 2.1.
DOS ODI Driver Name: EL90X.DOS  Size: 46KB Date: 3/21/97
NDIS Driver Name: El90X.386  Size: 55KB  Date: 12/20/96 

Microsoft Windows NT Server 3.51 machine that supports Net BEUI, 
NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Network Driver Optimization 

Normal

Full Duplex

Disabled

Boot PROM

Disabled

Media Type 

 10Base-T

I/O Base Address

FCC0h  (PCI)

Interrupt Request Level

9  (PCI)

Procedure

1

With the HP Vectra turned off, install the 3COM Etherlink  3C900 adapter 
card into a PCI slot.

2

Connect network cable media to the 3COM 3C900 card.

3

After booting, insert the 3COM’s drivers disk “Etherlink 3C900 Ethernet 
ver. 2.1”,  disk 1 of 2, and execute “A:\3C90XCFG.EXE.”

4

Select “CONFIGURE NIC,” and verify the resource settings listed above 
under the heading “Device Configuration.”

5

If changes are required, save those changes and exit.

6

Remove the 3COM drivers diskette and reboot the machine.

7

After windows loads, open the “NETWORK” program group, and double-
click on “Network Setup.”

8

Select the “Networks” button in the “Network Setup” dialog box.

Summary of Contents for Vectra VL6 6









































Reviews: