HP ProLiant XL270d Gen9 Maintenance And Service Manual Download Page 106 | Manualshive

Page: 106 / 126

background image

Item

LED

Status

Definition

Flashing green

The drive is rebuilding or performing
a RAID migration, strip size
migration, capacity expansion, or
logical drive extension, or is erasing.

Flashing amber/green

The drive is a member of one or
more logical drives and predicts the
drive will fail.

Flashing amber

The drive is not configured and
predicts the drive will fail.

Solid amber

The drive has failed.

Off

The drive is not configured by a
RAID controller.

IMPORTANT:

The Dynamic Smart Array B140i Controller is only available in UEFI Boot Mode. It cannot be
enabled in Legacy BIOS Boot Mode. If the B140i controller is disabled, drives connected to the
system board Mini-SAS connectors operate in AHCI or Legacy mode. Under this condition:

• The drives cannot be a part of a hardware RAID or a logical drive.

• The Locate, Drive status, and Do not remove LEDs of the affected drives are disabled.

Use BIOS/Platform Configuration (RBSU) in the

UEFI System Utilities

to enable or disable the

B140i controller (System Configuration

®

BIOS/Platform Configuration (RBSU)

®

System Options

®

SATA Controller Options

®

Embedded SATA Configuration).

GPU accelerator numbering

• Server left GPU accelerator numbering

106

GPU accelerator numbering

«
...
104
105
106
107
108
...
»

Summary of Contents for ProLiant XL270d Gen9































































































































Reviews:

No comments

Related manuals for ProLiant XL270d Gen9

Univerge SV8100

Brand: NEC Pages: 78

Univerge SV8100

Brand: NEC Pages: 186

Univerge SV8100

Brand: NEC Pages: 150

Univerge SV8100

Brand: NEC Pages: 52

Brand: IBM Pages: 106

SUPERSERVER 5018A-MHN4

Brand: Supermicro Pages: 116

SuperServer 6123L-8R

Brand: Supero Pages: 105

Brand: Infrant Technologies Pages: 98

Brand: Huawei Pages: 39

Brand: Huawei Pages: 188

5288 V3 V100R003

Brand: Huawei Pages: 297

Brand: Huawei Pages: 2

ProEdge-A100 thin client

Brand: ioCorp Pages: 30

T19 Hydro Server

Brand: BITMAIN Pages: 17

Brand: Kystar Pages: 81

Brand: Obvius Pages: 39

Brand: DEVA Pages: 90

Brand: TAG Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands