HP ProLiant BL460c Gen9 User Manual Download Page 16

Page: 16 / 90

Operations 16

Slide the access panel towards the rear of the server blade, and then lift to remove the panel.

Install the access panel

Place the access panel on top of the server blade.

Slide the access panel forward until it clicks into place.

Remove the DIMM baffles

The server contains two DIMM baffles.

Power down the server blade (on page

Remove the server blade (on page

Place the server blade on a flat, level work surface.

Remove the access panel (on page

If installed, remove the direct connect SATA cable ("

Remove the direct connect SATA cable

" on

page

If installed, remove the internal USB drive. To locate the internal USB connector, see "System board
components (on page

)."

IMPORTANT:

When removing the right DIMM baffle, leave the Smart Storage Battery

installed on the baffle. Use the blue pull tab to disconnect the Smart Storage Battery cable from
the system board.

Remove one or more DIMM baffles:

Summary of Contents for ProLiant BL460c Gen9



























































































Search results

Summary of Contents for ProLiant BL460c Gen9

Reviews:

Related manuals for ProLiant BL460c Gen9

Brands by name

Popular brands

HP ProLiant BL460c Gen9, User Manual

Search results

Summary of Contents for ProLiant BL460c Gen9

Reviews:

Related manuals for ProLiant BL460c Gen9

Brands by name

Popular brands