manualshive.com logo in svg

HP Pro 3330, Maintenance & Service Manual

The HP Pro 3330 Maintenance & Service Manual is a comprehensive resource for users seeking detailed instructions on maintaining and servicing their device. Available for free download at manualshive.com, this manual provides step-by-step guidance and troubleshooting tips to ensure optimal performance and longevity of your HP Pro 3330.

Share
Download
background image

Cleaning the Mouse

Before cleaning the mouse, ensure that the power to the computer is turned off.

●

Clean the mouse ball by first removing the retaining plate and the ball from the housing. Pull out
any debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly.

●

To clean the mouse body, follow the procedures in 

Cleaning the Computer Case on page 44

.

Service Considerations

Listed below are some of the considerations that you should keep in mind during the disassembly and
assembly of the computer.

Power Supply Fan

The power supply fan is a variable-speed fan based on the temperature in the power supply.

CAUTION:

The cooling fan is always on when the computer is in the “On” mode. The cooling fan is

off when the computer is in “Standby,” “Suspend,” or “Off” modes.

You must disconnect the power cord from the power source before opening the computer to prevent
system board or component damage.

Tools and Software Requirements

To service the computer, you need the following:

●

Torx T-15 screwdriver (HP screwdriver with bits, PN 161946-001)

●

Torx T-15 screwdriver with small diameter shank (for certain front bezel removal)

●

Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver)

●

Phillips #2 screwdriver

●

Diagnostics software

●

HP tamper-resistant T-15 wrench (Smart Cover FailSafe Key, PN 166527-001) or HP tamper-
resistant bits (Smart Cover FailSafe Key, PN 166527-002)

Screws

The screws used in the computer are not interchangeable. They may have standard or metric threads
and may be of different lengths. If an incorrect screw is used during the reassembly process, it can
damage the unit. HP strongly recommends that all screws removed during disassembly be kept with
the part that was removed, then returned to their proper locations.

CAUTION:

Metric screws have a black finish. U.S. screws have a silver finish and are used on hard

drives only.

CAUTION:

As each subassembly is removed from the computer, it should be placed away from the

work area to prevent damage.

46

Chapter 6   Routine Care and Disassembly Preparation

Summary of Contents for Pro 3330



































































































































































































































Reviews:

No comments

Related manuals for Pro 3330

FARONICS POWER SAVE MAC Getting Started Manual preview
POWER SAVE MAC
Brand: FARONICS Pages: 5
FARONICS POWER SAVE Product Data Sheet preview
POWER SAVE
Brand: FARONICS Pages: 2
FARONICS DEEP FREEZE ENTERPRISE Getting Started Manual preview
DEEP FREEZE ENTERPRISE
Brand: FARONICS Pages: 3
FARONICS ANTI-EXECUTABLE ENTERPRISE Getting Started Manual preview
ANTI-EXECUTABLE ENTERPRISE
Brand: FARONICS Pages: 2
Garmin GNC 420 Instructions Manual preview
GNC 420
Brand: Garmin Pages: 6
Emerson Smart Wireless Navigator Reference Manual preview
Smart Wireless Navigator
Brand: Emerson Pages: 22
Emerson Site Manager User Manual preview
Site Manager
Brand: Emerson Pages: 130
HP EliteBook 8460W Quickspecs preview
EliteBook 8460W
Brand: HP Pages: 41
HP Elite 7300 Microtower Illustrated Parts & Service Map preview
Elite 7300 Microtower
Brand: HP Pages: 4
HP MultiSeat ms6000 Hardware Reference Manual preview
MultiSeat ms6000
Brand: HP Pages: 63
HP EliteBook 8560p Brochure preview
EliteBook 8560p
Brand: HP Pages: 4
HP Elitebook 8560W Getting Started preview
Elitebook 8560W
Brand: HP Pages: 74
HP Fabric OS 7.0.0 Troubleshooting Manual preview
Fabric OS 7.0.0
Brand: HP Pages: 138
HP Evo D510 e-pc Technical Reference Manual preview
Evo D510 e-pc
Brand: HP Pages: 50
HP EliteBook 2560p Specifications preview
EliteBook 2560p
Brand: HP Pages: 34
HP FTAM/9000 Reference Manual preview
FTAM/9000
Brand: HP Pages: 102
HP NAS 1200s Release Note preview
NAS 1200s
Brand: HP Pages: 16
HP Evo D300 - Convertible Minitower Supplementary Manual preview
Evo D300 - Convertible Minitower
Brand: HP Pages: 2

Brands by name

Popular brands

Load more brands