HP OmniBook 4100 Service Manual Download Page 25

Page: 25 / 88

HP OmniBook 4100

Removal and Replacement

2-5

Removing the Hard Disk Drive

(User-Replaceable)

Table 2-5. Hard Disk Drive Replacement Part Numbers

Description

Part Number

Exchange
Part Number

Drive, hard disk (4.0GB, IBM)

0950-2671

F1386-69100

Drive, hard disk (4.0GB, Toshiba)

0950-2865

F1386-69101

Drive, hard disk (6.4GB, IBM)

0950-2785

F1475-69100

Required Equipment

•

Small Phillips screwdriver.

•

Small flat-blade screwdriver.

Removal Procedure

1. Unplug the ac adapter, if present, and remove the battery.

2. Turn the unit bottom side up.

3. Remove the hard drive screw from the bottom case.

4. Pull out the hard drive by its plastic tab.

Figure 2-3. Removing the Hard Disk Drive

5. If you are installing a new hard drive that does not have a cover, you can remove the cover parts

from the old hard drive:

•

Remove the screw from the case, then pry open the flap. If necessary, use a flat-blade
screwdriver

•

Use a flat-blade screwdriver to pry open the snaps at the ends of the case, then open the
connector-side of the case.

•

Pry out the corner next to the connector, then lift out the connector and hard drive together.

•

Unplug the internal connector and cable from the hard drive.

Screw, M3×4mm

Summary of Contents for OmniBook 4100

























































































Search results

Summary of Contents for OmniBook 4100

Reviews:

Related manuals for OmniBook 4100

Brands by name

Popular brands

HP OmniBook 4100, Service Manual

Search results

Summary of Contents for OmniBook 4100

Reviews:

Related manuals for OmniBook 4100

Brands by name

Popular brands