manualshive.com logo in svg

HP OmniBook 4100, Service Manual

Share
Download
HP OmniBook 4100 Service Manual Download Page 71

HP OmniBook 4100

Troubleshooting and Diagnostics

3-25

Time-out on AC

Sets whether power management time-outs occur while the ac
adapter is connected.

Disabled

Power Button Mode

Sets the action of the blue power button when pressed for less
than 4 seconds.

Suspend

Resume on Modem Ring

Sets whether the system resumes from Suspend if a ring
signal is received.

Enabled

Resume on Time of Day

Sets whether the system resumes from Suspend at a defined
time of day.

Disabled

Resume Time

Sets the 24-hour time when the system resumes from
Suspend if enabled.

Auto Suspend on Undock

Sets whether the OmniBook suspends after undocking.

When Lid Closed

Boot Menu

Default

Diskette Drive
Hard Drive
CD-ROM Drive

Shows the order of boot devices. Move the entries to change
the order.

1. Diskette drive
2. Hard drive
3. CD-ROM drive

Exit Menu

Save Changes and Exit

Saves Setup changes, exits, and reboots.

Discard Changes and Exit

Discards Setup changes since last save, exits, and reboots.
Does not affect Security and date/time changes.

Get Default Values

Restores default settings, stays in Setup. Does not affect
Security and date/time settings.

Load Previous Values

Discards Setup changes since last save, stays in Setup. Does
not affect Security and date/time changes.

Save Changes

Saves Setup changes, and stays in Setup. Security settings
are saved when changed.

Summary of Contents for OmniBook 4100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands