manualshive.com logo in svg

HP OmniBook 4100, Service Manual

Share
Download
HP OmniBook 4100 Service Manual Download Page 16

1-10

Product Information

HP OmniBook 4100

Preinstalled Software

Microsoft Windows 95 or Windows NT 4.0.
Windows 95-compatible Plug-and-Play.
Windows NT 4.0 APM and PC Card Plug-and-Play.
Advanced Power Management (APM 1.2).
DMI 2.0 with HP TopTools 2.6.
McAfee Virus Scan 3.1.5.
Online documentation.
OmniBook Recovery CD-ROM included.
Centralized worldwide BIOS and driver update service.

Security Features

User and administrator passwords.
System, hard drive, and docking passwords.
PC identification displayed at boot.
DMI-accessible electronic serial number.
Kensington Microsaver lock slot.

Environmental Limits

Operating temperature: 5 to 35 °C (41 to 95 °F).
Operating humidity: 20 to 90 percent RH (5 to 35 °C).
Storage temperature: –20 to 50 °C (–4 to 122 °F).

Major ICs

CPU: Intel Mobile Pentium or Pentium II.
South Bridge: PIIX4E.
Video: NeoMagic MagicGraph NM2160.
Audio: Crystal CS4237B.
CardBus: TI PCI1250A.
Keyboard controller: National PC87570.
Super I/O: SMC 769.

Summary of Contents for OmniBook 4100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands