HP Engage One Retail System 143 Hardware Reference Manual Download Page 40

Page: 40 / 65

Separate the computer’s display panel from the computer head unit at the connection points, and then

lift the display panel up approximately 2.5 cm (one inch).

IMPORTANT:

Do not lift the display panel higher than 2.5 cm (one inch) from the computer head unit.

An internal cable must be disconnected before the display panel can be fully removed.

Holding the display panel 2.5 cm (one inch) from the computer head unit, shift the display panel forward

no more than 7.5 cm (three inches) (1) to access the display cable connection. Lift the edges of the tape

that covers the display cable connection (2), and then disconnect the display cable from the connector

on the system board (3) by pulling the tab on the cable end.

IMPORTANT:

Be careful not to fold the edges of the tape. It must be replaced when the display cable is

reconnected.

Rotate the display panel over the top of the computer head unit and onto a flat surface covered by a soft

clean cloth.

IMPORTANT:

The touch and WLAN cables will still be connected between the top of the display panel

and the top of the computer head unit. Be careful when removing the display panel so that the cables do

not become disconnected.

Replacing the display panel

Follow the instructions below to replace the display panel on the computer head unit after replacing or

installing internal components.

Rotate the display panel over the computer head unit.

Chapter 3 Hardware configurations and upgrades

Summary of Contents for Engage One Retail System 143


































































Search results

Summary of Contents for Engage One Retail System 143

Reviews:

Related manuals for Engage One Retail System 143

Brands by name

Popular brands

HP Engage One Retail System 143, Hardware Reference Manual

Search results

Summary of Contents for Engage One Retail System 143

Reviews:

Related manuals for Engage One Retail System 143

Brands by name

Popular brands