manualshive.com logo in svg

HP E1328A, Service Manual, Page: 7 / 70

Share
Download
HP E1328A Service Manual Download Page 7

What’s in this Manual

Manual Overview 

This manual shows how to service the HP E1328A 4-Channel D/A Converter.  Additional manuals which may
be  required for servicing the D/A Converter include the HP E1328A User’s Manual which contains D/A
Converter operation, installation, and configuration information, and the appropriate mainframe user’s
manual(s) for mainframe operation, installation and configuration information.

Manual Content

Chapter

Title

Content

1

General
Information 

Provides a basic description, and lists available options and
accessories.  Also lists the tools and test equipment required for
service.

2

Installation

Procedures to install the D/A Converter, perform initial inspection,
prepare for use, and store and ship the D/A Converter.

3

Operating
Instructions

Procedures to operate the D/A Converter and perform operator’s
check.

4

Verification
Tests

Functional verification, operation verification, and performance
verification tests to test the D/A Converter.

5

Adjustments

Procedures to adjust the D/A Converter to within its rated
specifications.

6

Replaceable
Parts

Lists part numbers for user replaceable parts in the D/A Converter.
Provides information on ordering spare parts and module exchange.

7

Manual
Changes

Information to adapt this manual to instruments whose serial
numbers are lower than those listed on the title page.

8

Service

Procedures to aid in fault isolation and repair of the D/A Converter.

A

Calculating
D/A Converter
Accuracy

Shows how D/A Converter accuracy, measurement uncertainty,
and test accuracy ratios (TARs) are calculated.

B

Verification
Tests - C
Programs

Gives example C programs to implement the the verification tests
and adjustments.

What’s in this Manual

7

Summary of Contents for E1328A







































































Reviews:

No comments