HP E1328A Service Manual Download Page 16

Page: 16 / 70

Shipping
Guidelines

Follow the steps in Figure 2-1 to return the HP E1328A D/A Converter to a
Hewlett-Packard Sales and Support Office or Service Center.

1 Prepare the D/A Converter

•

Remove user wiring from the module

•

Attach tag to module/pod that identifies

- Owner
- Model Number/Serial Number
- Service Required

•

Place tagged device in approved anti-static bag

2 Package the D/A Converter

•

Place packaged D/A Converter in shipping carton*

•

Place 75 to 100 mm (3 to 4 inches) of shock-
absorbing material around the D/A Converter

•

Seal the shipping carton securely

•

Mark the shipping carton FRAGILE

3 Ship the D/A Converter to Hewlett-Packard

•

Place address label on shipping carton

•

Send carton to Hewlett-Packard

We recommend that you use the same shipping materials as those used in factory packaging (available from Hewlett-Packard). For

other (commercially-available) shipping materials, use a double wall-carton with minimum 2.4 MPa (350 psi) test.

Figure 2-1. Packaging/Shipping Guidelines

16 Installation

Chapter 2

Summary of Contents for E1328A







































































Search results

Summary of Contents for E1328A

Reviews:

HP E1328A, Service Manual, Page: 16 / 70

Search results

Summary of Contents for E1328A

Reviews: