HP Compaq dx2100 MT Series Service & Reference Manual Download Page 16

Page: 16 / 116

2–6

404569-001

Service Reference Guide, dx2100 MT

Setup Utilities and Diagnostics Features

Standard
CMOS
Features
(continued)

SATA Ch 0 Master
SATA Ch 1 Master

For each, allows you to:

• detect HDD size and head on selected channel
• set extended drive on selected channel to:

• None
• Auto

• set access mode on selected channel to

• Large
• Auto

• view

• Firmware version
• Capacity
• Cylinder
• Head
• Precomp
• Landing Zone
• Sector

• Run SMART HDD status check and self-test for selected

channel:
• SMART Status Check

•Target Disk
•SMART
•SMART Status Check

• SMART Short Self-Test

•Target Disk
•Estimated Test Time
•Start Test

• SMART Extended Self-Test

•Target Disk
•Estimated Test Time
•Start Test

Floppy Controller

Disables/enables the floppy disc controller.

Drive A

Allows you to set Drive A to None or 1.44, 3.5 in.

Halt On

Allows you to set POST error behavior to:

• All  Errors
• No  Errors
• All  but  Keyboard
• All  but  Diskette
• All but Diskette/Keyboard

Heading

Option

Description

Summary of Contents for Compaq dx2100 MT Series





















































































































Search results

Summary of Contents for Compaq dx2100 MT Series

Reviews:

Related manuals for Compaq dx2100 MT Series

Brands by name

Popular brands

HP Compaq dx2100 MT Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dx2100 MT Series

Reviews:

Related manuals for Compaq dx2100 MT Series

Brands by name

Popular brands