HP Compaq dx2100 MT Series Service & Reference Manual Download Page 10 | Manualshive

Page: 10 / 116

background image

1–2

404569-001

Service Reference Guide, dx2100 MT

Installing the Operating System

1.2 Converting to NTFS

1.2.1 Windows XP Home and XP Professional

The Windows XP Home and XP Professional operating systems handle only NTFS-formatted
drives. When installed, XP will, if necessary, automatically convert a FAT32 drive to NTFS.

1.3 HP

Software

The Microsoft Windows XP Home or Windows XP Professional operating system is preinstalled
on the computer and will be configured automatically the first time the computer is turned on. All
other software is user-installed.

Certain drivers and utilities are available only in selected languages. You can obtain the latest
version of these files, in English and selected other languages, in one of these ways:

■

HP web site at

■

Restore Plus!

CD, which is supplied with many Compaq models

✎

Additional HP software may be required in certain situations.

«
...
8
9
10
11
12
...
»

Summary of Contents for Compaq dx2100 MT Series





















































































































Reviews:

No comments

Related manuals for Compaq dx2100 MT Series

Brand: Olivetti Pages: 118

Nuvo-8108GC Series

Brand: Neousys Technology Pages: 142

Precision R5400

Brand: Dell Pages: 111

Brand: HP Pages: 108

Bc1500 - BladeSystem - Blade PC

Brand: HP Pages: 149

Compaq 18 All-in-One

Brand: HP Pages: 13

Compaq d538 CMT

Brand: HP Pages: 80

Brand: HP Pages: 7

Compaq dc7800 MT

Brand: HP Pages: 102

Brand: HP Pages: 105

Brand: HP Pages: 22

Compaq dc7800 Series

Brand: HP Pages: 276

Compaq dc7700 Ultra Slim Desktop (USDT) Business

Brand: HP Pages: 10

compaq d538 Series

Brand: HP Pages: 2

Compaq 8200 Elite Series

Brand: HP Pages: 65

Compaq 8200 Elite Series

Brand: HP Pages: 77

Compaq 8200 Elite Series

Brand: HP Pages: 4

Brand: HP Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands