HP AH226A - Smart Array E500/256MB Controller RAID Support Manual Download Page 56

Page: 56 / 72

NOTE:

To update SAS controller firmware online, you must be running

version 11.31.0909 or higher of the

sasd

driver. Online SAS controller firmware

updates are not supported on systems running HP-UX 11i v2.

If you do not specify the

-f

option with this command,

sasmgr

displays a

warning message before continuing. Otherwise, it suppresses the warning
message and executes the command.

enable

Enables the controller and brings it back online. This command causes the
driver to initialize the controller. Use this command to bring the controller
back online after using the

disable

command.

get_info

When the

get_info

command is run without qualifiers, it returns information

about the controller represented by

device_file

. The following qualifiers

may be specified with the

get_info

command:

•

lun

- Shows hardware path and SAS address information for a specific

LUN or all LUNs. If the

-N

option and the

-q lun=all

qualifier are

specified with this command, then it displays persistent device file
information.

•

lun_locate

- Shows LUN location information for the LUN specified

with the LUN qualifier. If the

-N

option and the

-q lun=all

qualifier

are specified with this command, then it displays persistent device file
information with the LUN location information.

•

pci_id

- Shows PCI ID information for the controller.

•

phy

- Shows information about all PHYs or a specific PHY.

•

phy_in_port

- Shows information about a port to which the specified

PHY belongs or provides information about all ports.

•

raid

- Shows RAID configuration information for the controller. If the

-N

option is specified with this command, then it displays persistent

device file information.

•

reg

- Displays the contents of a specific PCI config space or MMIO register

or all PCI config spaces or MMIO registers. PCI config space or MMIO
register type is specified with the reg_type qualifier. If

reg_type

is not

specified, then the command assumes a default register type of MMIO.

•

smp_addr

- Shows the SMP initiator SAS address to send SMP requests.

•

target

- Shows information about a specific target or all targets.

•

vpd

- Shows vital product data information for the controller.

get_stat

When the

get_stat

command is run without qualifiers, it shows statistics

about the controller represented by

device_file

. The following qualifiers

may be specified with the

get_stat

command:

•

phy

- Shows statistics for all PHYs or a specific PHY.

•

phy_in_port

- Shows statistics for a port to which the specified PHY

belongs to or provides statistics for all ports.

•

target

- Shows statistics for a specific target or all targets.

replace_tgt

The following qualifiers must be specified with the

replace_tgt

command:

•

old_dev

•

new_tgt_hwpath

Allows the

lun_dsf

specified with

old_dev

to be associated with a new SAS

target, which is specified with the

new_tgt_hwpath

qualifier. The

lun_dsf

must be the legacy device file and the

new_hw_path

must be the legacy

hardware path.

Configuring and Troubleshooting the Controller Online

Summary of Contents for AH226A - Smart Array E500/256MB Controller RAID









































































Search results

Summary of Contents for AH226A - Smart Array E500/256MB Controller RAID

Reviews:

Related manuals for AH226A - Smart Array E500/256MB Controller RAID

Brands by name

Popular brands

HP AH226A - Smart Array E500/256MB Controller RAID, Support Manual

Search results

Summary of Contents for AH226A - Smart Array E500/256MB Controller RAID

Reviews:

Related manuals for AH226A - Smart Array E500/256MB Controller RAID

Brands by name

Popular brands