HP AH226A - Smart Array E500/256MB Controller RAID Support Manual Download Page 71

Page: 71 / 72

B Specifications

HP 8 Internal Port SAS Controller Specifications

Table B-1 HP 8 Internal Port PCI-X SAS Controller Physical Specifications

16.8 x 6.4 x 1.6 cm

(6.6 x 2.5 x 0.6 in )

Dimensions (excluding bracket)

64-bit wide, PCI-X 133 MHz (1 GB/s maximum bandwidth)

Data Transfer Method

PCI-X-133 and 3.3 volt PCI compatibility only

PCI Bus Speed

PCI-X and 3.3 volt PCI compatibility only

PCI Compatibility

Table B-2 HP 8 Internal Port SAS Controller General Specifications (PCI-X and Embedded)

3 Gb/s SAS (Serial Attached SCSI)

Disk Drive and Enclosure Protocol Support

64-bit

Architecture

2 internal SFF8484 x4 Wide SAS Connectors

12 Gb/s per x4 Wide SAS Port (4 x 3 Gbps)

SAS Connectors

2 x4 Wide SAS Connectors

Simultaneous Drive Transfer Ports

12 Gb/s per x4 Wide SAS Port (4 x 3 Gb/s)

Port Transfer Rate

Yes (4MB flashable ROM)

Software-Upgradeable Firmware

1.168TB (8 x 146GB SAS Drives)

Maximum Capacity

64-bit, supporting servers with memory greater than 4 GB

Memory Addressing

Up to 2 Logical Volumes per RAID 1 array

Up to 10 disks total in all RAID volumes

Logical Drives Supported

RAID 1 (Mirroring)

RAID Support

HP 8 Internal Port SAS Controller Specifications

Summary of Contents for AH226A - Smart Array E500/256MB Controller RAID









































































Search results

Summary of Contents for AH226A - Smart Array E500/256MB Controller RAID

Reviews:

Related manuals for AH226A - Smart Array E500/256MB Controller RAID

Brands by name

Popular brands

HP AH226A - Smart Array E500/256MB Controller RAID, Support Manual

Search results

Summary of Contents for AH226A - Smart Array E500/256MB Controller RAID

Reviews:

Related manuals for AH226A - Smart Array E500/256MB Controller RAID

Brands by name

Popular brands