Adaptec 2940U - AHA Storage Controller Ultra SCSI 20 MBps User Manual Download | Manualshive

Page: 1 / 14

background image

1

Introduction

The Adaptec AHA

®

-2940Ultra and AHA-2940Ultra

Wide PCI-to-Fast SCSI host adapters provide a pow-
erful multitasking interface between your com-
puter’s PCI bus and SCSI devices (disk drives,
CD-ROM drives, scanners, tape backups, removable
media drives, etc.). Collectively, both host adapters
are referred to as the AHA-2940Ultra/2940Ultra
Wide. The following figures show the major compo-
nents on the AHA-2940Ultra and AHA-2940Ultra
Wide.

1

Adaptec AHA-2940

Ultra

50-pin 8-bit Internal

SCSI Connector

Host
Adapter
LED

AIC-78xx SCSI Protocol Chip

50-pin 8-bit

External

SCSI

Connector

Host Adapter

BIOS

LED Connector

Adaptec AHA-2940

Ultra Wide

50-pin 8-bit Internal

SCSI Connector

Host
Adapter
LED

AIC-78xx SCSI Protocol Chip

68-pin 16-bit

External

SCSI

Connector

LED Connector

Host Adapter

BIOS

68-pin 16-bit

Internal SCSI

Connector

1
2
3
...
»

Summary of Contents for 2940U - AHA Storage Controller Ultra SCSI 20 MBps















Reviews:

No comments

Related manuals for 2940U - AHA Storage Controller Ultra SCSI 20 MBps

BL-PA300KTA - High Definition Power Line Communication Ethernet Adaptor...

Brand: Panasonic Pages: 64

Brand: H3C Pages: 37

Brand: D-Link Pages: 1

2870W - annexe 1

Brand: SMC Networks Pages: 77

Brand: MillSO Pages: 2

Brand: TRENDnet Pages: 15

Brand: powerpack Pages: 9

Brand: Z-Com Pages: 46

Brand: Lindy Pages: 2

Brand: Emulex Pages: 19

Brand: ZyXEL Communications Pages: 28

Brand: Plantronics Pages: 12

Brand: Aaronn Pages: 2

73-30130-01261-5

Brand: Kvaser Pages: 25

Brand: Edimax Pages: 1

Brand: weintek Pages: 37

Brand: Sapido Pages: 34

Brand: Sapido Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands