manualshive.com logo in svg

HP A3100-16 v2 EI, Configuration Manual

The HP A3100-16 v2 EI Configuration Manual is a comprehensive guide that provides detailed instructions for setting up and optimizing your HP A3100-16 v2 EI switch. Download this manual for free from manualshive.com and unlock the full potential of your product with ease and confidence.

Share
Download
background image

 

•

 

Blackhole entries, which are manually configured and never age out. Blackhole entries are 

configured for filtering out frames with specific destination MAC addresses. For example, to block 

all packets destined for a specific user for security concerns, you can configure the MAC address of 
this user as a blackhole MAC address entry. 

To adapt to network changes and prevent inactive entries from occupying table space, an aging 

mechanism is adopted for dynamic MAC address entries. Each time a dynamic MAC address entry 

obtained or created, an aging time starts. If the entry has not updated when the aging timer expires, the 

switch deletes the entry. If the entry has updated before the aging timer expires, the aging timer restarts.  

 

 

NOTE: 

A static or blackhole MAC address entry can overwrite a dynamic MAC address entry, but not vice versa.

 

MAC address table-based frame forwarding 

When forwarding a frame, the switch adopts the following forwarding modes based on the MAC 

address table: 

•

 

Unicast mode: If an entry is available for the destination MAC address, the switch forwards the 
frame out of the outgoing interface indicated by the MAC address table entry. 

•

 

Broadcast mode: If the switch receives a frame with the destination address as all ones, or if no 
entry is available for the destination MAC address, the switch broadcasts the frame to all the 

interfaces except the receiving interface. 

Configuring the MAC address table 

The MAC address table configuration tasks include: 

•

 

Manually configuring MAC address table entries 

•

 

Disabling MAC address learning 

•

 

Configuring the aging timer for dynamic MAC address entries 

•

 

Configuring the MAC learning limit on ports 

These configuration tasks are all optional and can be performed in any order.  

 

 

NOTE: 

•

 

The MAC address table can contain only Layer 2 Ethernet ports and Layer 2 aggregate interfaces. 

•

 

This document covers configuring static, dynamic, and blackhole unicast MAC address table entries. For
more information about static multicast MAC address table entries, see the

 IP Multicast Configuration 

Guide. 

 

Manually configuring MAC address table entries 

To help prevent MAC address spoofing attacks and improve port security, you can manually add MAC 

address table entries to bind ports with MAC addresses. You can also configure blackhole MAC address 

entries to filter out packets with certain destination MAC addresses.  
Follow these steps to add, modify, or remove entries in the MAC address table in system view: 

18 

Summary of Contents for A3100-16 v2 EI


































































































































































































Reviews:

No comments

Related manuals for A3100-16 v2 EI

Eaton COOPER POWER SERIES Service Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 24
Eaton COOPER POWER SERIES Installation And Adjustment Instructions preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
Eaton Crouse-hinds series Manual preview
Crouse-hinds series
Brand: Eaton Pages: 16
Eaton Cutler-Hammer AMPGARD Instructions preview
Cutler-Hammer AMPGARD
Brand: Eaton Pages: 4
SAL PIXIE Smart Switch G3 Quick Start Manual preview
PIXIE Smart Switch G3
Brand: SAL Pages: 2
Movie Vision VCS-3 Installation And User Manual preview
VCS-3
Brand: Movie Vision Pages: 2
SMC Networks SMC8724-10BT Technical Specifications preview
SMC8724-10BT
Brand: SMC Networks Pages: 2
Omega Engineering PSW32 SERIES User Manual preview
PSW32 SERIES
Brand: Omega Engineering Pages: 8
Generac Power Systems GenReady Series 005448-2 Overview preview
GenReady Series 005448-2
Brand: Generac Power Systems Pages: 4
Eaton TM-1-8210 Series Instruction Leaflet preview
TM-1-8210 Series
Brand: Eaton Pages: 3
Grizzly H8239 Instructions preview
H8239
Brand: Grizzly Pages: 2
GarrettCom DS60s Installation And User Manual preview
DS60s
Brand: GarrettCom Pages: 39
Gefen EXT-UHDA-HBTL-RX User Manual preview
EXT-UHDA-HBTL-RX
Brand: Gefen Pages: 33
Microsonic zws-7/CD/QS Operating Instructions preview
zws-7/CD/QS
Brand: Microsonic Pages: 2
ROSSMA IIOT-AMS Tilt Counter Operation Manual preview
IIOT-AMS Tilt Counter
Brand: ROSSMA Pages: 13
AMX Enova DGX 100 Series Quick Start Manual preview
Enova DGX 100 Series
Brand: AMX Pages: 2
Emulex InSpeed 350 User Manual preview
InSpeed 350
Brand: Emulex Pages: 75
A10 Thunder series 930 Installation Manual preview
Thunder series 930
Brand: A10 Pages: 44

Brands by name

Popular brands

Load more brands