manualshive.com logo in svg

HP A3100-16 v2 EI, Configuration Manual

The HP A3100-16 v2 EI Configuration Manual is a comprehensive guide that provides detailed instructions for setting up and optimizing your HP A3100-16 v2 EI switch. Download this manual for free from manualshive.com and unlock the full potential of your product with ease and confidence.

Share
Download
background image

 

 

Assigning a trunk port to a VLAN 

A trunk port can carry multiple VLANs. You can assign it to a VLAN in interface view (including Ethernet 

interface view, Layer 2 aggregate interface view) or port group view. 
Follow these steps to assign a trunk port to one or multiple VLANs: 

To do… 

Use the command… 

Remarks 

Enter system view 

system-view 

— 

Enter Ethernet 
interface view 

interface

 interface-type 

interface-number

 

Enter Layer 2 
aggregate 

interface view 

interface bridge-aggregation 

interface-number

 

Enter interface 
view (including 

Ethernet 

interface view, 

Layer 2 
aggregate 

interface view) 

or port group 

view 

Enter port 
group view 

port-group manual 

port-group-name

 

Required 
Use either command. 

•

 

In Ethernet interface view, the 
subsequent configurations apply 

to the current port. 

•

 

In port group view, the 
subsequent configurations apply 

to all ports in the port group. 

•

 

In Layer 2 aggregate interface 
view, the subsequent 
configurations apply to the Layer 

2 aggregate interface and all its 

member ports. 

Configure the link type of the port 
or ports as trunk 

port link-type

 

trunk 

Required

 

Assign the trunk port(s) to the 
specified VLAN(s) 

port trunk permit vlan

 { 

vlan-id-list

 

| 

all

 } 

Required 
By default, a trunk port carries only 

VLAN 1. 

Configure the PVID of the trunk 
port(s) 

port trunk pvid vlan

 

vlan-id

 

Optional 
VLAN 1 is the PVID by default. 

 

 

NOTE: 

•

 

To change the link type of a port from trunk to hybrid or vice versa, you must set the link type to access
first. 

•

 

After configuring the PVID for a trunk port, you must use the 

port trunk permit vlan 

command to 

configure the trunk port to allow packets from the PVID to pass through, so that the egress port can 

forward packets from the PVID. 

•

 

After you use the 

port link-type

 { 

access

 | 

hybrid

 | 

trunk

 } command to change the link type of an 

interface, the loopback detection action configured on the interface by using the 

loopback-detection 

action

 command will be restored to the default. For more information about the 

loopback-detection 

action

 command, see the 

Layer 2—LAN Switching Command Reference.  

•

 

After you configure a command on a Layer 2 aggregate interface, the system starts applying the 
configuration to the aggregate interface and its aggregation member ports. If the system fails to do that
on the aggregate interface, it stops applying the configuration to the aggregation member ports. If it 

fails to do that on an aggregation member port, it skips the port and moves to the next port. 

 

100 

Summary of Contents for A3100-16 v2 EI


































































































































































































Reviews:

No comments

Related manuals for A3100-16 v2 EI

Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES How To Connect preview
LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES
Brand: Jabra Pages: 4
D-Link DES-3326SRM Product Manual preview
DES-3326SRM
Brand: D-Link Pages: 242
H3C S5170-EI Series Manual preview
S5170-EI Series
Brand: H3C Pages: 46
Techroutes S3756 Hardware Installation Manual preview
S3756
Brand: Techroutes Pages: 22
SMC Networks PF2A7 Series Operation Manual preview
PF2A7 Series
Brand: SMC Networks Pages: 43
GALCO EX95000 Series Quick Start Manual preview
EX95000 Series
Brand: GALCO Pages: 22
Hall Technologies EMCEE200 User Manual preview
EMCEE200
Brand: Hall Technologies Pages: 35
Greengate VNLW-P-1001-MV-N-V Installation Instructions preview
VNLW-P-1001-MV-N-V
Brand: Greengate Pages: 2
Key Digital HD Flash 4 KD-SW4x1 Operating Instructions Manual preview
HD Flash 4 KD-SW4x1
Brand: Key Digital Pages: 12
Tenda TEG3224P User Manual preview
TEG3224P
Brand: Tenda Pages: 177
Lindy 38032 User Manual preview
38032
Brand: Lindy Pages: 4
Hama AV Selector 310 Operating Instruction preview
AV Selector 310
Brand: Hama Pages: 21
Lindy 38042 Quick Start Manual preview
38042
Brand: Lindy Pages: 5
Kramer VS-24xl User Manual preview
VS-24xl
Brand: Kramer Pages: 11
Maiwe MISCOM7028GX Series User Manual preview
MISCOM7028GX Series
Brand: Maiwe Pages: 22
axing SPU 81-00 Operation Instructions preview
SPU 81-00
Brand: axing Pages: 4
I-Tech AVS801 User Manual preview
AVS801
Brand: I-Tech Pages: 22
Qvis poeswitch-4 Installation Manual preview
poeswitch-4
Brand: Qvis Pages: 7

Brands by name

Popular brands

Load more brands