manualshive.com logo in svg

HP A3100-16 v2 EI, Configuration Manual

The HP A3100-16 v2 EI Configuration Manual is a comprehensive guide that provides detailed instructions for setting up and optimizing your HP A3100-16 v2 EI switch. Download this manual for free from manualshive.com and unlock the full potential of your product with ease and confidence.

Share
Download
background image

 

Verification 

1.

 

Host A and Host C and ping each other successfully, but they both fail to ping Host B. Host B and 

Host D and ping each other successfully, but they both fail to ping Host A. 

2.

 

Determine whether the configuration is successful by displaying relevant VLAN information. 

# Display information about VLANs 100 and 200 on Device A: 

[DeviceA-Ethernet1/0/3] display vlan 100 

 VLAN ID: 100 

 VLAN Type: static 

 Route Interface: not configured 

 Description: VLAN 0100 

 Name: VLAN 0100 

 Tagged   Ports: 

    Ethernet1/0/3 

 Untagged Ports: 

    Ethernet1/0/1 

[DeviceA-Ethernet1/0/3] display vlan 200 

 VLAN ID: 200 

 VLAN Type: static 

 Route Interface: not configured 

 Description: VLAN 0200 

 Name: VLAN 0200 

 Tagged   Ports: 

    Ethernet1/0/3 

 Untagged Ports: 

    Ethernet1/0/2 

MAC-based VLAN configuration 

Introduction to MAC-based VLAN 

The MAC-based VLAN feature assigns hosts to a VLAN based on their MAC addresses. The following 

approaches are available for configuring MAC-based VLANs: 

Approach 1: Static MAC-based VLAN assignment 

Static MAC-based VLAN assignment applies to networks containing a small number of VLAN users. In 

such a network, you can create a MAC address-to-VLAN map containing multiple MAC 
address-to-VLAN entries on a port, enable the MAC-based VLAN feature on the port, and assign the port 

to MAC-based VLANs. 
With static MAC-based VLAN assignment configured on a port, the switch processes received frames by 

using the following guidelines: 

•

 

When the port receives an untagged frame, the switch looks up the MAC address-to-VLAN map 
based on the source MAC address of the frame for a match. If the MAC address of a MAC 

address-to-VLAN entry matches the source MAC address of the untagged frame, the switch tags the 

frame with the corresponding VLAN ID. If no match is found, the switch assigns a VLAN to the frame 
by using the following criteria in turn: protocols, and ports. 

103 

Summary of Contents for A3100-16 v2 EI


































































































































































































Reviews:

No comments

Related manuals for A3100-16 v2 EI

Eaton SOL30 Series Instruction Leaflet preview
SOL30 Series
Brand: Eaton Pages: 4
Thetford Marine TECMA Silence Marine Owner'S Manual preview
TECMA Silence Marine
Brand: Thetford Marine Pages: 9
Paugge ENT-MX20B16X16 User Manual preview
ENT-MX20B16X16
Brand: Paugge Pages: 20
RONK VIGILANT VTS0400 Owners & Installation Manual preview
VIGILANT VTS0400
Brand: RONK Pages: 32
Hisselektronik Safeline 2000 Light Manual For Programmering preview
Safeline 2000 Light
Brand: Hisselektronik Pages: 9
GE USB 2.0 7-Port Hub HO97916 Instruction Manual preview
USB 2.0 7-Port Hub HO97916
Brand: GE Pages: 19
IPGARD SDHN-4D-P Quick Start Manual preview
SDHN-4D-P
Brand: IPGARD Pages: 2
Uponor Smatrix Wave Plus Uahome Module R-167 Installation And Operation Manual preview
Smatrix Wave Plus Uahome Module R-167
Brand: Uponor Pages: 48
3onedata IES6300PRO Series Quick Installation Manual preview
IES6300PRO Series
Brand: 3onedata Pages: 5
WELLTECH WPoE-2426 User Manual preview
WPoE-2426
Brand: WELLTECH Pages: 280
Omron D4DS Manual preview
D4DS
Brand: Omron Pages: 11
ZIEHL-ABEGG S-ET Series Operating Instructions Manual preview
S-ET Series
Brand: ZIEHL-ABEGG Pages: 12
Intel True Scale Fabric 12000 Series Reference Manual preview
True Scale Fabric 12000 Series
Brand: Intel Pages: 125
Gefen EXT-HDFST-848CPN User Manual preview
EXT-HDFST-848CPN
Brand: Gefen Pages: 88
Eaton QSA400 Series Instruction Leaflet preview
QSA400 Series
Brand: Eaton Pages: 2
Cabletron Systems 9G421-02 Appendix preview
9G421-02
Brand: Cabletron Systems Pages: 12
Rose electronics VISTA KVL Quick Start Manual preview
VISTA KVL
Brand: Rose electronics Pages: 4
Advantage DDL12 Operation Manual preview
DDL12
Brand: Advantage Pages: 14

Brands by name

Popular brands

Load more brands