HP 669048-009 Installation Manual Download Page 13

Page: 13 / 108

100 Kilo Sliding Shelf kit 13

Extend the inner slides of the sliding rail until the screw holes on the sliding rail and the left rail with fixed

brackets are aligned. Gently push down on the sliding rail to lock it into place.

Secure the rails together with two M4 x 12 flat HD screws and M4 external washers.

Repeat steps 1 through 4 for the right rail with fixed brackets.

Installing the sliding shelf rail assemblies

WARNING:

To reduce the risk of personal injury or damage to the equipment, be sure to secure

mounted rack components when moving the rack.

You must install the sliding shelf rail assemblies before installing the sliding shelf. Follow these steps closely

to install the sliding shelf rail assemblies into the rack:

Summary of Contents for 669048-009













































































































Search results

Summary of Contents for 669048-009

Reviews:

Related manuals for 669048-009

Brands by name

Popular brands

HP 669048-009, Installation Manual

Search results

Summary of Contents for 669048-009

Reviews:

Related manuals for 669048-009

Brands by name

Popular brands