HP 512424-001 Maintenance And Service Manual Download Page 99

Page: 99 / 154

4–54

Maintenance and Service Guide

Removal and replacement procedures

✎

The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink assembly and the system
board each time the fan/heat sink assembly is removed:

■

Thermal paste is used on the processor

and the heat sink section

that services it.

■

Thermal pads are used on the Northbridge chip

and the heat sink section

that services it.

■

Thermal pads are used on the other system board components

and sections of the heat sink

that

service them.

Replacement thermal material is included with all system board, fan/heat sink assembly, and processor spare
part kits.

Reverse this procedure to install the fan/heat sink assembly.

Summary of Contents for 512424-001



























































































































































Search results

Summary of Contents for 512424-001

Reviews:

Related manuals for 512424-001

Brands by name

Popular brands

HP 512424-001, Maintenance And Service Manual

Search results

Summary of Contents for 512424-001

Reviews:

Related manuals for 512424-001

Brands by name

Popular brands