HP 1810-24 Management And Configuration Manual Download Page 52 | Manualshive

Page: 52 / 71

background image

Table 30 LLDP Local Device Fields

(continued)

Description

Field

Displays the system capabilities of the local system that are supported and enabled.
The default is Bridge.

Capabilities Enabled

LLDP Interface Description

The interface on which LLDP 802.1AB frames can be transmitted.

LLDP Interface

The description of the selected port associated with the local system.

Port Description

The source of the port identifier.

Port ID

Displays the type of the source of the port ID.

Port ID Subtype

Click the

Refresh

link above the page to update the page with the latest data from the switch.

LLDP Remote Device

Use the LLDP Remote Device page to view information about remote devices for which the switch
has received LLDP information.

To display the Remote Device page, click

LLDP > Remote Device

in the navigation pane.

Figure 38 LLDP Remote Device Page

Table 31 LLDP Local Device Fields

Description

Field

The port on the local system that received the LLDP data from the remote system.

Local Interface

The chassis component associated with the remote system.

Chassis ID

The physical address of the port on the remote device that sent the LLDP data.

Port ID

The port description configured on the remote device. If the port description is not
configured, the field is blank.

Port Description

The system description configured on the remote device. If the system description is not
configured, the field is blank.

System Name

The capabilities on the remote device.

System Capabilities

The capabilities on the remote device that are enabled.

Capabilities Enabled

IP address of the remote device.

System IP

Click the

Refresh

link above the page to re-display the page with current settings from the switch.

Energy Efficient Ethernet

EEE (Energy Efficient Ethernet) is designed to save power by turning off network ports that are not
passing traffic. EEE includes a mechanism to awaken the port when it needs to send or receive
traffic. The transmitter sends LPI (low power idle) signals instead of the normal idle signals to indicate
that the EEE protocol is in effect. After a period of time called Ts (time to sleep), the transmitter
stops sending signals and the link is quiet. When the transmitter needs to send traffic, it begins

52

Link Layer Discovery Protocol (LLDP)

«
...
50
51
52
53
54
...
»

Summary of Contents for 1810-24








































































Reviews:

No comments

Related manuals for 1810-24

Brand: IBM Pages: 88

Brand: Datavideo Pages: 58

Brand: Lantronix Pages: 2

EtherDevice EDS-4009 Series

Brand: Moxa Technologies Pages: 18

Brand: TP-Link Pages: 2

GenReady Series 005448-2

Brand: Generac Power Systems Pages: 4

Brand: Omron Pages: 16

SmartNode 4658 Series

Brand: Patton electronics Pages: 12

Brand: Setra Systems Pages: 4

Brand: Enttec Pages: 22

Brand: VADA Pages: 4

Brand: Orbis Pages: 2

Brand: MiLAN Pages: 12

ProSAFE FS526Tv2

Brand: NETGEAR Pages: 20

Brand: Scion-Tech Pages: 9

Brand: Wave Italy Pages: 32

Brand: Hama Pages: 12

Brand: Cabletron Systems Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands