manualshive.com logo in svg

HP 10Gb Ethernet BL-c, Command Reference Manual

The HP 10Gb Ethernet BL-c module is a high-performance networking solution for your business needs. Unlock its full potential by referring to the comprehensive Command Reference Manual. Download the manual for free from manualshive.com and explore the advanced features and functionalities that this product offers.

Share
Download
background image

 

 

 

Information Menu  59  

 

 

IP information 

Command:

  

/info/l3/ip

 

IP information: 

Interface information: 

  1: 10.80.23.243    255.255.254.0   10.80.23.255,   vlan 1, up 

250: 10.20.7.144     255.255.0.0     10.20.255.255,  vlan 4095, up 

 

Default gateway information: metric strict 

  1: 10.80.22.1,      vlan any,  up  active     

254: 10.20.1.1,       vlan 4095, up  active     

 

Current ServerMobility settings: OFF 

ServerMobility ports:  empty 

DHCP request filtering enabled ports:  empty 

Relay on non-ServerMobility ports: Ena 

Active-Backup ports: 

Current IP forwarding settings: OFF, dirbr disabled 

 

Current network filter settings: 

  none 

 

Current route map settings: 

 

The following interface and default gateway information is displayed:  

•

 

Interface number 

•

 

IP address 

•

 

IP mask 

•

 

IP broadcast address 

•

 

Operational status 

•

 

BootP relay settings 

•

 

Server Mobility settings 

•

 

IP forwarding settings 

•

 

Network filter settings 

•

 

Route map settings 

Summary of Contents for 10Gb Ethernet BL-c





































































































































































































































Reviews:

No comments

Related manuals for 10Gb Ethernet BL-c

Omega Engineering 430 Instruction Sheet preview
430
Brand: Omega Engineering Pages: 3
AVE 8PSWT Specification preview
8PSWT
Brand: AVE Pages: 2
GHIELMETTI 674.115.420.30 Operation Manual preview
674.115.420.30
Brand: GHIELMETTI Pages: 12
AdLuminis 324002 Quick Start Manual preview
324002
Brand: AdLuminis Pages: 8
Dahua DH-PFS3005-5ET-L Quick Start Manual preview
DH-PFS3005-5ET-L
Brand: Dahua Pages: 13
H3C H3C S5800-32F Installation Manual preview
H3C S5800-32F
Brand: H3C Pages: 110
GE Digital Energy STS-400-25-3 Installation And Operating Manual preview
Digital Energy STS-400-25-3
Brand: GE Pages: 49
SUCO 0140 Series Operating Instructions preview
0140 Series
Brand: SUCO Pages: 2
Jerguson SAS-16 Installation, Operation & Maintenance Instructions preview
SAS-16
Brand: Jerguson Pages: 4
Raritan SwitchMan USB-Combo SW4 Quick Installation And Setup Manual preview
SwitchMan USB-Combo SW4
Brand: Raritan Pages: 2
TRENDnet TE100-S16plus User Manual preview
TE100-S16plus
Brand: TRENDnet Pages: 32
Xcellon SH10-10H Manual preview
SH10-10H
Brand: Xcellon Pages: 2
Eaton Moeller IZM Series Quick Start Manual preview
Moeller IZM Series
Brand: Eaton Pages: 4
Hailink MX44NN00RK User Manual preview
MX44NN00RK
Brand: Hailink Pages: 6
Cabletron Systems SmartSTACK ELS100-24TXG Release Note preview
SmartSTACK ELS100-24TXG
Brand: Cabletron Systems Pages: 7
APG FT-100 Series Operator'S Manual preview
FT-100 Series
Brand: APG Pages: 7
LEGRAND Chief Kontour KPWR Series Installation Instructions Manual preview
Chief Kontour KPWR Series
Brand: LEGRAND Pages: 8
ENSIM SENSORS DX-ELB 11 Operating Manual preview
DX-ELB 11
Brand: ENSIM SENSORS Pages: 15

Brands by name

Popular brands

Load more brands