Hoval BelariaSR04I3, Installation Manual

Page: 78 / 236

Installation manual
12
Bela08+16I3
Hoval BelariaSRM
4P330420-1A – 2012.11
4 211 846 / 00 – 11/12
4 Configuration
Thermostats
Digital I/O PCB
Alarm output logic
Demand PCB
Energy metering
4.2.4 Quick wizard: Capacities (energy metering)
# Code Description
[A.2.2.4] [C-05] External room thermostat for the main
zone:

1 (Thermo ON/OFF): When the
used external room thermostat or
heat pump convector can only send
a thermo ON/OFF condition. No
separation between heating or
cooling demand.

2 (C/H request): When the used
external room thermostat can send
a separate heating/cooling thermo
ON/OFF condition.
[A.2.2.5] [C-06] External room thermostat for the
additional zone:

0: N/A

1 (Thermo ON/OFF): When the
used external room thermostat or
heat pump convector can only send
a thermo ON/OFF condition. No
separation between heating or
cooling demand.

2 (C/H request): When the used
external room thermostat can send
a separate heating/cooling thermo
ON/OFF condition.
[A.2.2.B] [C-08] External sensor:

0 (No): NOT installed.

1 (Outdoor sensor): Connected to
PCB measuring the outdoor
temperature.

2 (Room sensor): NOT applicable.
# Code Description
[A.2.2.6.1] [C-02] External backup heat source:

0 (No): None

1 (Bivalent): Gas, oil boiler

2: N/A

3: N/A
[A.2.2.6.3] [C-09] Alarm output on optional
SammelalarmBS PCB:

0 (Normally open): The alarm
output will be powered when an
alarm occurs.

1 (Normally closed): The alarm
output will NOT be powered when
an alarm occurs. This installer
setting allows distinction between
detection of an alarm and
detection of a power failure to the
unit.
See also table below (Alarm output
logic).
[A.2.2.6.4] [F-04] Bottom plate heater

0 (No): NOT installed

1 (Yes): Installed
[C-09] Alarm No alarm
No power
supply to unit
0 (default) Closed output Open output Open output
1 Open output Closed output
# Code Description
[A.2.2.7] [D-04] Demand PCB
Only applicable for Bela08 and
Belar08. Indicates if the
optional demand PCB is installed.

0 (No): NOT installed

1 (Yes): Installed
# Code Description
[A.2.2.8] [D-08] Optional external kWh meter 1:

0 (No): NOT installed

1: Installed (0.1 pulse/kWh)

2: Installed (1 pulse/kWh)

3: Installed (10 pulse/kWh)

4: Installed (100 pulse/kWh)

5: Installed (1000 pulse/kWh)
[A.2.2.9] [D-09] Optional external kWh meter 2:

0 (No): NOT installed

1: Installed (0.1 pulse/kWh)

2: Installed (1 pulse/kWh)

3: Installed (10 pulse/kWh)

4: Installed (100 pulse/kWh)

5: Installed (1000 pulse/kWh)
# Code Description
[A.2.3.1] [6-02] Booster heater capacity [kW]
[A.2.3.6] [6-07] Bottom plate heater capacity [W]
4P330420-1A - 2012.11_offset.book Page 12 Thursday, December 13, 2012 3:35 PM