Hotpoint ULTIMA FDW80 Service Information Download Page 7

7

PROGRAMME GUIDE

Cycle

Cycle Selection 

Instructions

Cycle

Description

Detergent 

for

Pre-Wash

& Wash

Rinse

Aid

Wash Cycle 

Duration - Mins

(without extra 

drying)

Intensive

Very dirty dishes and pans 
(not to be used for delicate 
items)

Pre-wash with hot water at 
40°C

Extended wash at 65°

2 cold rinses

Hot rinse at 65°C

Drying

5 + 25 g

*

120

Normal

Cycle for normally dirty 
pans and dishes.

Standard daily cycle

Wash at 55°C

Cold rinse

Hot rinse at 70°C

Drying

30 g

*

72

Eco

Environmentally friendly 
cycle with low energy 
consumption levels, 
suitable for normally dirty 
pans and dishes

2 cold pre-washes

Extended wash at 45°C

Hot rinse at 65°C

Drying

5 + 25 g

*

120

Fast

Economic and fast cycle 
to be used for slightly dirty 
dishes.

Run cycle immediately 
after use.

Without drying except 
when the extra drying 
option has been selected.

Short wash at 40°C

Hot rinse at 62°C

25 g

*

(with

extra

drying)

25

Pre-Wash

Preliminary wash cycle for 
dishes while awaiting 
completion of the load 
with the dishes from the 
next meal.

Short cold wash to prevent food 
drying onto the dishes

-

-

12

Delicates

Special cycle to be used 
for more delicate items 
which are sensitive to high 
temperatures.

Run cycle immediately 
after use

Wash at 50°C

Rinse at 45°C

Hot rinse at 65°C

Drying

25 g

*

96

Special 

Guest

Rinse and drying cycle for 
dishes that are seldom 
used and are only dusty.

Hot rinse at 65°C

Drying

-

*

36

OPTIONAL WASH CYCLE

Auto

Duo-Wash

Wash differentiated on the 
two racks.

Delicate for glassware 
and glasses on the upper 
rack and heavy duty for 
the pans on the lower 
rack.

Cold Pre-Wash

Wash at 50°C

Lukewarm rinse at 45°C

Hot rinse at 65°C

Drying

5 + 25g

*

108

Summary of Contents for ULTIMA FDW80





























Reviews: