1
5
G
B
Do not position blinds
behind the cooker or
less than 200 mm awa
y
from its sides.
An
y
hoods must be
installed according to
the instructions listed in
the relevant operating
manual.
L
evell
i
ng
If it is necessar
y
to level the
appliance, screw the
adjustable feet into the places
provided on each corner of the
base of the cooker (
see
figure
).
The legs* fit into the slots on
the underside of the base of
the cooker.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min.
mm.
420
Min.
mm.
* Onl
y
available in certain models.
E
l
ec
t
r
i
c
a
l
c
onn
ec
ti
on
s
Install a standardised plug corresponding to the
load indicated on the appliance data plate (
see
Technical data table
).
The appliance must be directl
y
connected to the
mains using an omnipolar circuit-breaker with a
minimum contact opening of 3 mm installed between
the appliance and the mains. The circuit-breaker
must be suitable for the charge indicated and must
compl
y
with NFC 15-100 regulations (the earthing
wire must not be interrupted b
y
the circuit-breaker).
The suppl
y
cable must be positioned so that it does
not come into contact with temperatures higher than
50°C at an
y
point.
Before connecting the appliance to the power
suppl
y
, make sure that:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the ma
x
imum power of
the appliance, which is indicated b
y
the data plate.
The voltage is in the range between the values
indicated on the data plate.
The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use e
x
tension cords or multiple sockets.
Once the appliance has been installed, the power
suppl
y
cable and the electrical socket must be
easil
y
accessible.
The cable must not be bent or compressed.
The cable must be checked regularl
y
and replaced
b
y
authorised technicians onl
y
.
The
m
a
nu
f
a
c
t
urer
decl
i
nes
a
n
y
l
ia
b
i
l
i
t
y
should
t
hese
s
a
f
e
t
y
me
a
sures
no
t
b
e
o
b
served
.
G
a
s
connec
t
i
on
Connection to the gas network or to the gas c
y
linder
ma
y
be carried out using a fle
x
ible rubber or steel
hose, in accordance with current national legislation
and after making sure that the appliance is suited to
the t
y
pe of gas with which it will be supplied (see
the rating sticker on the cover: if this is not the case
see below
). When using liquid gas from a c
y
linder,
install a pressure regulator which complies with
current national regulations. To make connection
easier, the gas suppl
y
ma
y
be turned sidewa
y
s*:
reverse the position of the hose holder with that of
the cap and replace the gasket that is supplied with
the appliance.
Check that the pressure of the gas suppl
y
is consistent
with the values indicated in the Table of burner and
nozzle specifications (
see below
). This will ensure the
safe operation and durabilit
y
of
y
our appliance while
maintaining efficient energ
y
consumption.
G
a
s
connec
t
i
on
us
i
ng
a
f
le
x
i
b
le
ru
bb
er
hose
Make sure that the hose complies with current
national legislation. The internal diameter of the hose
must measure: 8 mm for liquid gas suppl
y
; 13 mm
for methane gas suppl
y
.
Once the connection has been performed, make
sure that the hose:
Does not come into contact with an
y
parts that
reach temperatures of over 50°C.
Is not subject to an
y
pulling or twisting forces
and that it is not kinked or bent.
Does not come into contact with blades, sharp
corners or moving parts and that it is not
compressed.
Is eas
y
to inspect along its whole length so that
its condition ma
y
be checked.
Is shorter than 1500 mm.
Fits firml
y
into place at both ends, where it will be
fi
x
ed using clamps that compl
y
with current
regulations.