background image

 

3

 

 

HH18Bi 22/04/13 

 

 
 

3

 

Installation Instructions 

 
 

WARNINGS AND IMPORTANT SAFETY INFORMATION 

 

 
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION! 

These instructions cover the basic principles to ensure satisfactory installation of the stove, although detail may need slight 
modification to suit particular local site conditions. In all cases the installation must comply with current local regulations 
including Building Regulations, Local Authority Byelaws and other specifications or regulations including Ireland, UK or 
EU standards referred to as they affect the installation of the stove. Approved Document J is particularly important for 
England and Wales and can be downloaded for no cost at: 

http://www.planningportal.gov.uk/england/professionals/en/4000000000503.html

 Also of importance are Approved 

documents L1 A and B conservation of fuel and power. The Domestic Heating Compliance Guide will also be found useful. 

 
Important Chimney Warning 

This stove must not

 

be installed into a chimney that serves any other heating appliance. 

 

Extractor Fan Warning 

There must not be an extractor fan fitted in the same room as the stove as this can cause the stove to emit 
fumes into the room. 

  
Cleaning and Chimney Sweeping 
The appliance, flue & chimney must be cleaned and checked internally and externally regularly in use 
and especially after a period on disuse (e.g. after summer). 

Lift down the baffle at least weekly to check 

for build up of soot or debris on the top from the flue pipe. Remove the baffle and check the flue spigot and 
connector is fully clear at regular intervals. The chimney and flue connector must be swept at least annually, 
more often when used with sooty fuels or damp wood. Any loose, broken or leaking joints or flue ways 
MUST be repaired immediately. 
 

Fuels 

Only use recommended fuels. The appliance can be damaged by burning pallets or treated wood, petroleum 
coke, anthracite, liquid fuels or general rubbish and this will invalidate your warranty and risk your personal 
safety. 

The appliance must not be used as a rubbish incinerator

. Any coal type fuel that is used must be 

suitable for a closed appliance. Arigna Ecobrite or similar would be a recommended fuel. 
 

Maintenance 

Annual checking and servicing of the appliance and flue by a competent engineer is recommended. 
 

 
Ventilation 

Adequate ventilation is ESSENTIAL for the safe and efficient operation of any solid fuel or wood burning 
appliance. Ventilation MUST be provided where required by the stove output or flue under-performance. 
Keep all ventilation clear and free of blockage. 
 

External Ducted Air 

This appliance is suitable to accept ducted external air which should be provided in accordance with best 
practices and minimum distances to combustibles should be adhered to. It is recommended that a 4” plastic 
pipe is used to bring the air in from outside. It is recommended to run the air vent from opposite poles of the 
dwelling and tee off for the air supply to the stove. An aluminium duct should be used to connect from the 
4” pipe to the stove. The inlet pipe should be suitable located to prevent ingress of moisture and where it 

Summary of Contents for HD18Bi






















Reviews: