Hot Shot 810-T Manual Download

Page: 1 / 14

Pg.

HOW IT WORKS

MOUNTING

CODE SWITCH SETTINGS

BATTERY BACKUP

TRANSMITTER FUNCTION SWITCH SETTINGS

INDICATOR LEDS

TEST BEACON

BASIC PIVOT INSTALLATION

REINKE PIVOTS

VALLEY 4000, 6000, AND PANELS WITH 3 SEC DELAY PCB.

VALLEY 8000, PRO PANEL, SELECT PANEL AND SIMILAR

L ELECTRIC PANEL

ENGINE DRIVEN PIVOT AND T

L ENGINE PIVOT (ISUZU PANEL)

ZIMMATIC PIVOT 10 WIRE SYSTEM

ZIMMATIC PIVOT 11 WIRE SYSTEM

UNIT # SETTINGS

GROUNDING

Version : 160825

Hot Shot Systems Inc. will no longer sell or warranty its products for the use in controlling or monitoring pollu-

tants. However, the use of these controllers in non pollutant applications such as water tanks, water pumps, pivots,

irrigation systems and any other monitoring or control applications that do not involve pollutants are suitable for

these products.

IRRIGATION

810

TRANSMITTER GUIDE

Summary of Contents for 810-T















Search results

Summary of Contents for 810-T

Reviews:

Related manuals for 810-T

Brands by name

Popular brands

Hot Shot 810-T, Manual

Search results

Summary of Contents for 810-T

Reviews:

Related manuals for 810-T

Brands by name

Popular brands