background image

8

 

 

Ⅱ. OPERATING INSTRUCTIONS. 

CAUTION

Do not put your hand into the back of the storage bin or the right side pump.   
The ice on the evaporator may drop off

a hard block of ice may suddenly   

break down, or pump motor may suddenly start-up

resulting in injury

 

 

 

 

 

 

 

NOTICE

All parts are factory-adjusted. Improper adjustments may result in failure.
If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor.

 

   

HYGINEN

This icemaker is designed to produce edible ice. To keep the icemaker hygienic: 
*Wash your hands before removing ice. Use the plastic scoop provided (accessory). 
*The storage bin is for ice use only. Do not store anything else in the bin, nor use other electrical appliances in the bin. 
*Clean the storage bin before use (see "III.1. CLEANING"). 
*Keep the scoop clean. Clean it by using neutral cleaner and rinse thoroughly. 
*Close the door after removing ice to prevent entrance of dirt, dust or insects into the storage bin.

 

 

1. START UP 

The installer will normally commission the icemaker to start the automatic icemaking process. To ensure continuous operation. 
Make sure that: 
 
*The water supply tap is on, and 
*The icemaker is connected to the power supply. 

 

2. PREPARING THE ICEMAKER FOR LONG STORAGE 

NOTICE

This icemaker will not work at subfreezing temperatures. To prevent damage to the water supply line, drain the icemaker 
when air temperature is below zero. 

 

HYGIENE

When shutting down the icemaker for two or more days, drain the icemaker to prevent contamination in the water circuit.

  1) Unplug the icemaker or disconnect the power supply. 
  2) Close the water supply tap, and remove the inlet hose.

 

  3) Remove all ice from the storage bin, and clean the bin. 
  4) Ask for draining of the icemaker by professional qualified personnel. 

 

 

Water Tank

Storage Bin

Summary of Contents for SRM-105A


















Reviews: