background image

23

11) Remove the front panel.

12) Move the flush switch to the “FLUSH” position to drain the remainder of the solution.

13) After the solution is drained, move the flush switch to the “ICE” position.

14) Replace the front panel in its correct position.

15) Open the water supply line shut-off valve and supply water to the reservoir.

16) When the gear motor starts, remove the front panel and turn off the power supply.

17) Drain out all water from the water line. See 2) and 3).

18) Move the flush switch to the “ICE” position and run the icemaker.

19) Turn off the power supply after 30 minutes.

20) Pour warm water into the storage bin to melt all ice, and then clean the bin liner with the

solution.

21) Flush out any solution from the storage bin.

22) Turn on the power supply and start the automatic icemaking process.

IMPORTANT

1. After cleaning, do not use ice made from the sanitizing solution. Be careful

not to leave any solution in the storage bin.

2. Follow carefully any instructions provided with the bottles of cleaning or

sanitizing solution.

3. Never run the icemaker when the reservoir is empty.

Summary of Contents for SRC-10H


























Reviews: