4
1) Prepare a plastic bucket.
Pull out the cap, salt water
hose and filter from the salt
water tank, and put them
into the bucket.
2) Use the measuring cup (accessory)
to add one level cup (approx.
700ml) of sodium chloride (NaCl) or
potassium chloride (KCl) into the salt
water tank.
3) Add water into the salt water tank up
to the 5 L line.
4) Check that the mini cap is closed, and put
the cap on the salt water tank. Shake it
until sodium chloride or potassium chloride
completely dissolves in the water.
5) Open the mini cap and put it in the recess,
and push in the salt water hose until the
stopper hits the cap.
Stopper
Measuring
Cup
Salt
Cap
Shake well
4. PURGING SALT WATER PUMP
This unit uses a pump to supply salt water. If the salt water pump
contains air, electrolyzed water cannot be dispensed properly. When
the unit is installed for the first time or when the add salt water lamp
on the operation panel comes on, purge air from the salt water pump
as follows:
1) Check that there is enough salt water in the salt water tank.
2) Check that the power switch (earth leakage circuit breaker) is off.
Turn it off if it is on.
3) Turn the power switch back on.
4) Press the dispense button on the operation panel.
5) Check that the add salt water lamp is on.
6) Press the reset button.
7) The pump starts running and pumping up the salt water to purge
the salt water hose. About 90 seconds later, the pump stops.
8) The unit drains water to flush out the electrode before shutting
down. The add salt water lamp goes off.
* Do not press the dispense button on the
operation panel, the power switch or any
other switches before the add salt water
lamp goes off. Otherwise, the lamp cannot
be reset, and the above procedure must be
repeated from step 5). Wait until the unit
flushes out the system and completes the
resetting procedure.
* Always locate the salt water tank below the
end of the water outlets, or the salt water
tank will leak salt water by siphonage and
the unit may fail to operate properly.
5. START UP
1) Plug in the unit.
2) Open the water supply line shut-off valve.
3) Check for proper operation of the water softener. Refer to the
instruction manual provided for operating instructions. See “9.
[f] WATER HARDNESS (WEEKLY)” for how to check for water
softening.
4) Check that the salt water tank is properly set up.
5) Turn on the power switch (earth leakage circuit breaker). A
mechanical sound is heard three times immediately after the power
switch is turned on. This is not a sign of failure.
6) Press the dispense button on the operation panel.
7) The operation lamp comes on.
8) The ready lamp starts flashing, and non-electrolyzed water is
dispensed at first.
9) When the unit starts to dispense electrolyzed water of the intended
quality, the ready lamp stays on continuously.
10) Check that the add salt water lamp is off. If it is on, follow “4.
PURGING SALT WATER PUMP” to supply salt water to the
electrolytic cell until the lamp goes off.
11) To stop dispensing water, press the dispense button on the
operation panel again. The ready lamp goes off. The unit goes
through the flush cycle before water stops.
* While the ready lamp is flashing, the quality of electrolyzed water
has not reached the intended level. If the available chlorine
concentration and pH value are less than the specified values,
sanitizing water may not provide a sufficient bactericidal effect.
* Before using electrolyzed water, check that the ready lamp stays on.
6. SHUT DOWN
1) For daily shutdown, press the dispense button on the operation
panel. The ready lamp flashes for about 3 seconds and the unit
stops dispensing electrolyzed water. To restart the unit, press the
dispense button on the operation panel.
2) For long storage, see “10. PREPARING ELECTROLYZER FOR
LONG STORAGE”.
7. WATER FAILURE
In case of water failure, follow the instructions below:
1) Shut down the unit according to “6. SHUT DOWN”.
2) Wait until water supply is resumed.
3) Check that the water supply valve is closed.
4) Open the drain valve.
5) Open the water supply line shut-off valve. Drain water until no rusty
water comes out.
6) Close the drain valve.
7) Start up the unit according to “5. START UP”.
Water Outlet
Ends
Salt Water Tank
Cap
Salt Water
Hose
Salt Water
Tank