background image

3

CONTENTS

Important Safety Information ................................................................................................. 4
I. Specifications ...................................................................................................................... 6

A. Electrical and Refrigerant Data ..................................................................................... 6

1. KMS-830MLJ ........................................................................................................... 6
2. SRK-10J .................................................................................................................. 6

B. Dimensions/Connections .............................................................................................. 7

1. KMS-830MLJ ........................................................................................................... 7
2. SRK-10J .................................................................................................................. 8

II. Installation and Operating Instructions .............................................................................. 9

A. Location ........................................................................................................................ 9

1. Icemaker .................................................................................................................. 9
2. Remote Condensing Unit ....................................................................................... 10

B. Checks Before Installation ............................................................................................11

1. Icemaker .................................................................................................................11
2. Remote Condensing Unit ........................................................................................11

C. How to Remove Panels ............................................................................................... 12

1. Icemaker ................................................................................................................ 12
2. Remote Condensing Unit ....................................................................................... 12

D. Setup ........................................................................................................................... 13

1. Dispenser Unit/Ice Storage Bin and Icemaker Setup ............................................. 13
2. Bin Control Installation ........................................................................................... 14

E. Installation of the Remote Condensing Unit ................................................................ 15

1. Setup ...................................................................................................................... 15
2. Line Set ................................................................................................................. 15
3. Line Set Installation ............................................................................................... 16

F. Electrical Connection ................................................................................................... 18
G. Water Supply and Drain Connections ......................................................................... 21
H. Final Checklist ............................................................................................................. 23
I. Startup .......................................................................................................................... 24

III. Maintenance ................................................................................................................... 26

A. Maintenance Schedule ................................................................................................ 26
B. Cleaning and Sanitizing Instructions ........................................................................... 27

IV. Preparing the Icemaker for Periods of Non-Use ............................................................. 32
V. Disposal ........................................................................................................................... 33

IMPORTANT

This manual should be read carefully before the appliance is installed and operated. 
Read the warnings and guidelines contained in this manual carefully as they 
provide essential information for the continued safe use and maintenance of the 
appliance. Retain this manual for any further reference that may be necessary.

Summary of Contents for KMS-830MLJ



































Reviews: