Hoshizaki KM-590DJ Instruction Manual Download Page 11

Page: 11 / 23

ENGLISH

Upper Unit Wire Harness

Connector B (not used)

6) Level the icemaker and storage bin in both the

left-to-right and front-to-rear directions. Adjust the
storage bin legs to make the icemaker level.7

7)Replace the panels and storage bin baﬄ e in their

correct positions unless you are installing an upper
unit. If installing an upper unit, see "II.E. Installation
of Upper Unit."

E. Installation of Upper Unit

1) See "II.D. Setup" for the lower unit installation.
2) Remove the top panel and the top insulation of the

lower unit. The top panel and the top insulation of
the lower unit are not required when installing an
upper unit.

3) Unpack the upper unit and remove the shi1pping

carton, tape, and packing material.

4) Remove the panels of the upper unit.
5) Stack the upper unit on top of the lower unit.
6) Secure the upper unit to the lower unit using the

2 mounting brackets and the bolts provided. See
Fig. 5.

7) Remove the bin control cable bracket from inside

the upper unit. See Fig. 6. Leave the upper unit's bin
control assembly in its original position. It will not be
used.

8) Route lower unit wire harness connector B through the

hole in the bottom of the upper unit. Route the wiring
through the bushing in the bin control cable bracket,
then through the wire saddles.

9) Connect lower unit wire harness connector B to upper

unit wire harness connector A.
Note: Wire harness is connected to the control board

red K4 connector.

10) Make sure the wire harnesses are secured in the wire

saddles and do not interfere with any components.

11) Secure the bin control cable bracket.
12) Replace the panels and storage bin baﬄ e in their

correct positions.

Fig. 5

Bin

Icemaker
(Upper Unit)

Icemaker

(Lower Unit)

Mounting

Brackets

Bolts

Fig. 6

Bin Control

Cable Bracket

Control Board Red

K4 Connector

Upper Unit Wire Harness

Wire Saddle

Lower Unit Wire Harness Connector B/

Upper Unit Wire Harness Connector A

Lower Unit

Wire Harness

Control

Board

Red K4

Connector

Upper Unit Connection Detail

See "II.D. Setup" for

Lower Unit

Connection

Control Board Red

K4 Connector

Upper Unit Connection Overview

Lower Unit Wire Harness

Connector B

Upper Unit

Wire Harness

Connector A

Upper Unit Wire

Harness

Connector B (not used)

Summary of Contents for KM-590DJ
























Search results

Summary of Contents for KM-590DJ

Reviews:

Related manuals for KM-590DJ

Brands by name

Popular brands

Hoshizaki KM-590DJ, Instruction Manual

Search results

Summary of Contents for KM-590DJ

Reviews:

Related manuals for KM-590DJ

Brands by name

Popular brands