background image

5

 WARNING, continued

• Children should be properly supervised around the appliance.
• Do not climb, stand, or hang on the appliance or allow children or animals to do so. 

Serious injury could occur or the appliance could be damaged.

• Do not use combustible spray or place volatile or flammable substances near the 

appliance. They might catch fire.

• Keep the area around the appliance clean. Dirt, dust, or insects in the appliance 

could cause harm to individuals or damage to the appliance.

Additional Warning for Remote Models
• 

THE REMOTE CONDENSER UNIT MUST BE GROUNDED. The power supply and 

ground connection to the remote condenser unit are supplied from the icemaker. 
Failure to properly ground the remote condenser unit could result in death or 
serious injury.

• Wire routing (conduit) and disconnect (if required) must meet national, state, and 

local electrical code requirements. Failure to meet these code requirements could 
result in death, electric shock, serious injury, fire, or damage.

NOTICE

• Follow the water supply, drain connection, and maintenance instructions carefully to 

reduce the risk of costly water damage.

• In areas where water damage is a concern, install in a contained area with a floor 

drain. 

• Install the icemaker in a location that stays above freezing. Normal operating 

ambient temperature must be within 45°F to 100°F (7°C to 38°C).

• Do not leave the icemaker on during extended periods of non-use, extended 

absences, or in sub-freezing temperatures. To properly prepare the icemaker for 
these occasions, follow the instructions in "IV. Preparing the Icemaker for Periods of 
Non-Use."

• Do not place objects on top of the appliance.
• The dispenser unit/ice storage bin is for ice use only. Do not store anything else in 

the dispenser unit/ice storage bin.

Summary of Contents for KM-340MAJ







































Reviews: