background image

PREFACE                                         01 SEPTEMBER 1998                                                        PAGE 2

HE500OCS050/051 User Manual

PREFACE

This manual explains how to use the Horner Electric HE500OCS050 and HE500OCS051.

Copyright (C) 1998 Horner Electric, Inc., 640 North Sherman Drive Indianapolis, Indiana 46201.  All rights
reserved.  No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior agreement and written
permission of Horner Electric, Inc.

All software described in this document or media is also copyrighted material subject to the terms and
conditions of the Horner Software License Agreement.

Information in this document is subject to change without notice and does not represent a commitment on
the part of Horner Electric, Inc.

Cscape is a trademark of Horner Electric, Inc.

CsCAN is a trademark of Horner Electric, Inc.

DeviceNet is a trademark of the Open DeviceNet Vendor Association, Inc.

For user manual updates, contact Horner Electric Advanced Products
Group, Technical Support Division, at (317) 916-4274 or visit our
website at www.heapg.com.

Summary of Contents for HE500OCS050






















Reviews: