HORNE T105A Installation, Operating And Maintenance Instructions Download Page 3

Horne Engineering Ltd 

Issue 7, November 2018 

 

 

 

 

3

 

Fig 1 

Fig 2 

4)  Mark out the 4 Support Holes 

Ensure  that  the  enclosure  is 
hanging true and then mark out the 
holes  for  the  2  upper  support 
screws.  Remove the bottom cover 
of  the  pre-plumbed  enclosure  and 
mark  out  the  2  lower  support 
screws (See Fig 3). 

 

 

5)  Drill Support Holes 

Carefully remove the pre-plumbed 
enclosure from the temporary 
support screw and, being careful 
not to scratch the enclosure or its 
covers, lay it down where it will not 
be damaged.  Drill the 4 holes and 
install the wall plugs. 
 

6)  Attach  the  Pre-Plumbed  Enclosure 

to the Wall 

Carefully  re-hang  the  pre-plumbed 
enclosure  on  the  temporary  screw. 
Put the four supplied screw bushes 
in  the  mounting  holes  in  the  panel 
and  then  attach  the  panel  firmly  to 
the  wall  by  the  four  supplied 
stainless  steel  screws.    A  bead  of 
silicon  mastic  can  be  used,  if 
required, to cover any gaps behind 
the  panel  on  uneven  walls.  Do  not 
mastic  the  lower  End  Cap  to  the 
wall.  See Fig 4. 

 

Fig 3 

 

 
 
 

 

 

 

Summary of Contents for T105A

















Reviews: