background image

16

EN

DE

FR

IT

17

EN

DE

FR

IT

Replacing the Vertical Fin

To replace the vertical fin on your Night Vapor, follow the steps listed below.

1.  Gently remove the clear pressure fitting tube located on the bottom of the aircraft. 

2. Gently disconnect the pushrod from the control horn.
3.  Slide the vertical fin out of the mounting column.

4.  Reconnect the pushrod to the new vertical fin, and slide the vertical fin into the housing.
5.  Slide the clear pressure fitting tube back into place.

Note:  When replacing the pressure fitting tube, do not jam it against the column; this will not allow the 

vertical fin to move freely throughout its range of motion.

Replacing the Wing

All LEDs on the wing are permanently attached. The new wing will include a new set of LEDs. To replace the 

wing follow the steps below:

1. Disconnect the main LED wire from the receiver board. 

 

2. Remove the LED that is attached to the tail of the aircraft.

 

Note:  The LED is tack glued to the fuselage and it will be necessary to very carefully break the glue 

joint loose.

3. Loosen the four screws on the wing mounting columns, and gently pull the wing off.

4. Slide the new wing back into place, and tighten the wing to the mounting columns.
5.  Install the LED located near the tail, and tack glue it into place. Then, reconnect the main LED wire to 

the receiver board.

Note:  Use only a very small amount of hot glue or rubber cement to attach the LED to the fuselage. 

Other adhesives may damage the LED. 

Summary of Contents for Night Vapor BNF














Reviews: