EN
16
Night Timber X 1.2m
Problem
Possible Cause
Solution
Aircraft will not
respond to throttle
but responds to other
controls
Throttle not at idle and/or throttle trim too high
Reset controls with throttle stick and throttle trim at lowest setting
Throttle servo travel is lower than 100%
Make sure throttle servo travel is 100% or greater
Throttle channel is reversed
Reverse throttle channel on transmitter
Motor disconnected from ESC
Make sure motor is connected to the ESC
Extra propeller noise
or extra vibration
Damaged propeller and spinner, collet or motor
Replace damaged parts
Propeller is out of balance
Balance or replace propeller
Prop nut is too loose
Tighten the prop nut
Reduced fl ight
time or aircraft
underpowered
Flight battery charge is low
Completely recharge fl ight battery
Propeller installed backwards
Install propeller with numbers facing forward
Flight battery damaged
Replace fl ight battery and follow fl ight battery instructions
Flight conditions may be too cold
Make sure battery is warm before use
Battery capacity too low for flight conditions
Replace battery or use a larger capacity battery
Aircraft will not Bind
(during binding) to
transmitter
Transmitter too near aircraft during binding process
Move powered transmitter a few feet from aircraft, disconnect and reconnect
fl ight battery to aircraft
Aircraft or transmitter is too close to large metal
object, wireless source or another transmitter
Move aircraft and transmitter to another location and attempt binding again
The bind plug is not installed correctly in the bind port
Install bind plug in bind port and bind the aircraft to the transmitter
Flight battery/transmitter battery charge is too low
Replace/recharge batteries
Bind switch or button not held long enough during bind process
Power off transmitter and repeat bind process. Hold transmitter bind button or
switch until receiver is bound
Aircraft will not
connect (after
binding) to
transmitter
Transmitter too near aircraft during connecting process
Move powered transmitter a few feet from aircraft, disconnect and reconnect
fl ight battery to aircraft
Aircraft or transmitter is too close to large metal
object, wireless source or another transmitter
Move aircraft and transmitter to another location and attempt connecting again
Bind plug left installed in bind port
Rebind transmitter to the aircraft and remove the bind plug before cycling power
Aircraft bound to different model memory
(ModelMatch
TM
radios only)
Select correct model memory on transmitter
Flight battery/Transmitter battery charge is too low
Replace/recharge batteries
Transmitter may have been bound to a different aircraft
using different DSM protocol
Bind aircraft to transmitter
Control surface does
not move
Control surface, control horn, linkage or servo damage
Replace or repair damaged parts and adjust controls
Wire damaged or connections loose
Do a check of wires and connections, connect or replace as needed
Transmitter is not bound correctly or the incorrect airplanes
was selected
Re-bind or select correct airplanes in transmitter
Flight battery charge is low
Fully recharge fl ight battery
BEC (Battery Elimination Circuit) of the ESC is damaged
Replace ESC
Controls reversed
Transmitter settings are reversed
Perform the Control Direction Test and adjust the controls on transmitter appropriately
Motor power pulses
then motor loses
power
ESC uses default soft Low Voltage Cutoff (LVC)
Recharge fl ight battery or replace battery that is no longer performing
Weather conditions might be too cold
Postpone flight until weather is warmer
Battery is old, worn out, or damaged
Replace battery
Battery C rating might be too small
Use recommended battery
Troubleshooting Guide
Troubleshooting Guide AS3X
Problem
Possible Cause
Solution
Oscillation
Damaged propeller or spinner
Replace propeller or spinner
Imbalanced propeller
Balance the propeller
Motor vibration
Replace parts or correctly align all parts and tighten fasteners as needed
Loose receiver
Align and secure receiver in fuselage
Loose aircraft controls
Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface)
Worn parts
Replace worn parts (especially propeller, spinner or servo)
Irregular servo movement
Replace servo
Inconsistent fl ight
performance
Trim is not at neutral
If you adjust trim more than 8 clicks, adjust the clevis to remove trim
Sub-Trim is not at neutral
No Sub-Trim is allowed. Adjust the servo linkage
Aircraft was not kept immobile for 5
seconds after battery connection
With the throttle stick in lowest position. Disconnect battery, then reconnect battery and keep the
aircraft still for 5 seconds
Incorrect response
to the AS3X Control
Direction Test
Incorrect direction settings in the
receiver, which can cause a crash
DO NOT fl y. Correct the direction settings (refer to the receiver manual), then fl y
