background image

11

EN

The USB battery charger (EFLC1013) included with your aircraft has been 

designed to safely charge the 1S 3.7V 500mAh 25C Li-Po fl ight battery.

NOTICE:

 Inspect the battery to make sure it is not damaged e.g., swollen, 

bent, broken or punctured. Charge only batteries that are cool to the touch 

and are not damaged.

1. Insert the charger into a USB port. The charger only uses power from 

the USB port. USB power supplies, such as those used to charge cellular 

phones, can also be used.

2. Connect the battery to the 

charger as shown in the 

illustration above. When 

you make the connection successfully, the LED on the charger turns solid 

red, indicating charging has begun. Charging a fully discharged (not over-

discharged) 500mAh battery takes approximately 60 minutes. The LED 

goes out when the charge is complete.

CHARGING

 (

Solid Red LED

)

MAX CHARGE

 (

LED OFF

)

3. Always disconnect the fl ight battery from the charger immediately upon 

completion of charging.

CAUTION:

 Once charging is complete, immediately remove the 

battery. Never leave a battery connected to the charger.

USB Li-Po

Charger

EFLC1013

SOLID RED LED

–Charging

DC Input:5.0V    500mA

DC Output:4.2V    500mA

LED OFF

–Charge 

Complete

Summary of Contents for BLH9600















































Reviews: