Horizon Fitness SPF-20A Manual Download Page 83

Page: 83 / 106

4. Stitcher Head

4-2 Stitcher Attachment

This section shows how to attach stitcher
heads to SPF-20A.

Turn off the power switch.

Loosen hold block with T-wrench from

the front side of stitcher. And slide in hold
block from the side of stitcher head holder.

Insert driver into groove of drive bar.

Align the stitcher with the clincher.

Fit the gauge (accessory) on the side.
Align the stitcher and the clincher so that
there is no gap in between.

Fix hold block with T-Wrench.

Attach the detection bar (accessory) on
the sticher head on operation side.

- Follow the procedures below to check the

position of the detection bar.

Remove the sticher unit front cover (two
fixing screws).

Drive Bar

Driver

Stitcher Head Holder

Hold Block

T-Wrench

Stitcher

Clincher

Gauge

Fix Screws

Stitcher

CAUTION

- Insert hold block into stitcher head
holder completely. Otherwise, the
machine may be damaged.

Stitcher Unit
Front Cover

Fixing Screw

Summary of Contents for SPF-20A











































































































Search results

Summary of Contents for SPF-20A

Reviews:

Related manuals for SPF-20A

Brands by name

Popular brands

Horizon Fitness SPF-20A, Manual

Search results

Summary of Contents for SPF-20A

Reviews:

Related manuals for SPF-20A

Brands by name

Popular brands