5
6
ASSEMBLY STEP 5
HARDWARE BAG FOR STEP 5 CONTENTS :
A) Open HARDWARE BAG FOR
STEP 5.
B) Remove PRE-ATTACHED BOLT &
WASHERS from CONSOLE MAST.
C) Slide UPPER HANDLEBARS onto
CONSOLE MAST and attach by
re-inserting PRE-ATTACHED BOLT
And one Pre-Spring Washer And one Flat
Washer .
D) Attach LOWER HANDLEBARS to
UPPER HANDLEBARS using PRE-
ATTACHED SCREWS.
E) Attach HANDLEBAR COVERS
using 2 SCREWS (A).
(F) Repeat on the other side.
ASSEMBLY STEP 6
SCREWS(A)
CONSOLE
MAST
HANDLEBAR
COVER
PRE -
-
ATTACHED
BOLT & WASHER
PRE
ATTACHED SCREWS
LOWER HANDLEBAR
LINKAGE PIECE
Flat Washer (A)
Wave Washer (B) Flat Washer (C)
BOLT (D)
SCREW (A)
4x15L
Qty: 4
A) Open the hardware bag for the step 6.
B) Attach the linkage arm onto the pedal arm
pin using (A),(B),(C),(D) one by one.
C)Remove the pre-attached washers (E), nut
(H), screw (G) &linkage axle (F) from the
linkage piece.
D)Put the linkage axle (F) into the linkage
tube,and then attach the linkage arm inside
the lower handlebar linkage piece using 2
washers (E),1 screw (G), and 1 nut (H).
E) Remove the two pre-attached screws (I)
from the end of the lower handlebar Attach
the handlebar covers onto the lower
handlebar using (I).
F) Repeat on the other side.
Qty: 2
Qty: 2
Qty: 2
HARDWARE BAG FOR STEP 6 CONTENTS :
16.2x 28.7x1.5t
Flat Washer (A)
Wave Washer (B)
Flat Washer (C)
BOLT (D)
16.7x 22.5x0.3t
8.5x 25.0x1.5t
M8x1.25Px12L
LINKAGE ARM
PEDAL ARM
LINKAGE TUBE
Qty: 2
Qty: 2
PRE-ATTACHED HARDWARE PARTS:
Flat Washer (E)
Linkage axle (F)
Qty:1
Teflon Washer (A)
10.4x 24.75x1.5t
Qty: 4
Nylon Nut (B)
M10x1.5P
Qty: 2
HARDWARE BAG FOR STEP 4 CONTENTS :
NYLON NUT(B)
PIVOT-TUBE
PEDAL ARM
Teflon Washer (A)
Teflon Washer (A)
PRE-ATTACHED SCREW (C)
Pre-attached screw(C)
REAR WHEEL COVER
PEDALARM COVER
A) Open the hardware bag for the step 4.
B) Place the pedal arm onto the pivot-
tube using 2 TEFLON WASHERS(A)
AND 1 NYLON NUT(B).
C) Remove 2 pre-attached screws (C)
from the two ends of the pedal arm
and then attach the pedal arm cover
to the pedal arm using 1 pre-attached
screw (C).
D) Put the rear wheel cover onto the
end pedal arm using 1 pre-attached
screw (C).
E) Repeat on the other side.
(I)
(H)
(G)
(E)
(F)
(E)
(I)
screw (G)
Qty:1
screw (I)
Qty:2
nut (H)
Qty:1
