Hoover HVRC1800010, Owner'S Manual

Page: 8 / 16

8
Ret our nez l’app arei l.
Pla cez l a cou rro ie e n V dan s la r ain ure d e l’a git ate ur.
Rep lac ez l’a git ate ur e n in sér ant le bo uto n s aill ant ca rré da ns
l’o uve rtu re c orr esp ond ant e sur l e côt é de l a bus e.
Pui s, i nsé rez l e bou ton s aill ant r ond d e l’a git ate ur d ans
l’o uve rtu re c orr esp ond ant e de l a bus e.
Ret our nez l ’ap par eil e t fai tes t our ner l a pou lie f olle
pou r vou s ass ure r que l a cou rro ie p lat e et l a cou rro ie
en V s ont b ien i nst allé es.
Rep lac ez l e cou ver cle e t la p laq ue i nfé rie ure .
Rem ett ez e n pla ce l es v is d u cou ver cle e t de l a
pla que i nfé rie ure .
Ser rez l es v is à l ’ai de d ’un t our nev is.
Las courroies : Quoi acheter
N’u tili ser po ur vot re asp ira teu r q ue des cou rro ies
de m arq ue HO OV ER. Po ur l’a cha t d ’un e n ouv elle
cour roi e p lat e, d em and er la piè ce H oov er
no 385 280 36. Po ur l’a cha t d ’un e n ouv elle co urr oie
en V , d em and er la piè ce H oov er n o. 3 852 8013 .
2.12
A
Remplacement de la courroie en V
2.8 2.10
2.11
2.9
Dég age z la c our roi e
pla te du mot eur et de
la p oul ie f olle .
En p laç ant l es l ett res à l ’ex tér ieu r en V , pla cez l a
cou rro ie d ans l a rai nur e du p oul ie f olle .
Ens uite , pou sse z la c our roi e dan s l’o uve rtu re s itu ée
sou s l’ appar eil.
En p laç ant l es l ett res à l ’ex tér ieu r, g lis sez l a cou rro ie
pla te aut our de la po ulie fo lle et de la po ulie du
mot eur.
Ret our nez l’app arei l
et d éga gez la co urr oie
usé e de l a pou lie f olle .
Ret our nez l’a ppa rei l e t re tire z le s
der niè res v is d e la p laq ue i nfé rie ure d e
la f aço n ind iqu ée.
Ret ire z la p laq ue i nfé rie ure .
Sou lev ez l’a git ate ur e t r eti rez la
cour roi e u sée.
A A
A
B B
B
C C
C
D D
Dég age z la c our roi e usé e du m ote ur e t de l a pou lie f olle .
En pla çan t le s le ttre s à l’e xtér ieu r, g lis sez la nou vel le cour roi e a uto ur d e la po ulie
fol le e t de l a pou lie d u mot eur .
Fai tes t our ner l a pou lie f olle a fin d e vou s ass ure r que l a cou rro ie e st b ien i nst allé e.
Ref erm ez l e cou ver cle , ret our nez l ’ap par eil e t rem ett ez l es v is e n pla ce e n pre nan t
soi n de l es s err er a vec u n tou rne vis .
Remplacement de la courroie plate
2.7
A
B
C
D
Las courroies (cont.)
8
Turn cleaner over.
Place V-belt into groove of agitator.
Reposition agitator by sliding square projection on belt end
of agitator into square slot on side of nozzle.
Then slide round projection on other end of agitator into
round slot.
Turn cleaner over and roll idler pulley to make
sure flat belt and V-belt are positioned properly.
Reposition hood and bottom plate.
Replace hood and bottom plate screws.
Tighten screws with screwdriver.
Belts: What to Buy
Use only genuine HOOVER belts with your
cleaner. When purchasing a new Flat Belt, ask for
HOOVER part No. 38528036. When purchasing a
new V-Belt, ask for HOOVER part No. 38528013.
2.12
A
Replacing V-Belt
2.8 2.10
2.11
2.9
Remove flat belt from
motor and idler pulley.
With lettering on outside of new V-belt, position belt
into groove of idler pulley.
Then push belt through opening on bottom of cleaner.
With lettering on outside of flat belt, position belt
around idler and motor pulley. Turn cleaner over and
remove old belt from
idler pulley.
Turn cleaner over and remove remaining
bottom plate screws as shown.
Remove bottom plate.
Pull out agitator and slide off
old belt.
A A
A
B B
B
C C
C
D D
Remove old belt from motor and idler pulleys.
With lettering on outside of new belt, slip belt around idler and motor pulley.
Roll idler pulley to make sure belt is positioned properly.
Reposition hood, turn cleaner over and replace screws. Tighten with screwdriver.
Replacing Flat Belt
2.7
A
B
C
D
The Belts (cont.)