background image

Carefully pull out used bag. 

8

3 - 2

3 - 3

3 - 4

B

A

Form new bag into a box-like shape.
Slide bag collar 

firmly

into holder.

Push rear edge of bag into bag cavity
below seal (A).  

Clear bag opening (B) by pushing the
pierced paper through opening toward
bag interior.

Close bag lid.

How to attach bag lid 

The bag lid and hinges are designed
with a “break- away” feature.  If the lid is
pushed open too far, it will come off.  It
can be easily re-attached by aligning the
hinges with the appropriate slots in the
cleaner, as shown. 

Filters-
secondary and micro

How to clean 

Disconnect cleaner from electrical
outlet.

The 

secondary filter

, located behind

the grill in the bag compartment, pro-
tects the motor from dirt particles.  If fil-
ter becomes dirty, pull off grill and lift out
filter.  Wash filter in warm water or
replace it with a new one.  A 

dry

filter

must be put back into cleaner.

Do not operate cleaner without sec-
ondary filter in place.

3 - 5

3 - 6

Familiarize yourself with these home
maintenance tasks as proper use and
care of your cleaner will ensure contin-
ued cleaning effectiveness.

Filter bag 

When to replace 

Check the bag when the “CHECK BAG”
indicator shows red.  When bag is filled
with dirt, the cleaner will not operate effi-
ciently.  Discard used bag.

CAUTION: Very fine materials, such
as face powder, cornstarch, fireplace
ashes or fireplace soot, may seal the
paper bag and may cause it to burst
even though it is only partially full of
dirt. When the cleaner is used to
remove material of this nature,
change the bag often.

3. Maintenance

Where to buy

Filter bags may be purchased from
Authorized Hoover Dealers (Depots),
Leading Retailers, Hoover Factor y
Service Centers, or through The Hoover
Company online at
www.hoover.com

What to buy 

In order to maintain the original cleaning
effectiveness and superior filtration qual-
ities of your cleaner, use only 

Genuine

HOOVER®  Allergen Filtration Type S

disposable filter bags.  
Regular 

HOOVER® Type S

disposable

bags also fit your cleaner and will give
satisfactory performance.

To assure that your HOOVER cleaner
operates at peak performance, it is
imperative that you use only genuine
HOOVER filter bags made by The
Hoover Company.  HOOVER bags can
be identified by these trademarks—  

®

3 - 1

How to replace 

Disconnect cleaner from electrical
outlet.

Rotate hose to the side, lift bag lid latch
and open bag lid.        

Continued 

Summary of Contents for Commercial WindTunnel















Reviews: